- 您現在的位置：買賣IC網 > PDF目錄361357 > T63H0008A-CX (TM Technology, Inc.) Li-Ion/Polymer Battery for one-cell Protector PDF資料下載
參數資料
| 型號： | T63H0008A-CX |
| 廠商： | TM Technology, Inc. |
| 英文描述： | Li-Ion/Polymer Battery for one-cell Protector |
| 中文描述： | Li-Ion/Polymer電池單細胞保護 |
| 文件頁數： | 10/20頁 |
| 文件大?。?/td> | 341K |
| 代理商： | T63H0008A-CX |
TE
CH
tm
Description of Operation
T63H0008A
TM Technology, Inc. reserves the right
P. 10
Publication Date: Dec. 2003
to change products or specifications without notice. Revision:A
Normal condition
The T63H0008A monitors the voltage of the battery connected between VDD and VSS pin and the voltage
difference between V- and VSS pin to control charging and discharging. When the battery voltage is in the
range from the over-discharge detection voltage (VDET2) to the overcharge detection voltage (VDET1), and
the V- pin voltage is in the range from the charger detection voltage (VDET5) to the over-current 1 detection
voltage (VDET3), the IC turns both the charging and discharging controlFETs on. This condition is called the
normal condition, and in this condition charging and discharging can be carried out freely.
Note:
When a battery is connected to the IC for the first time, the battery may not enter dischargeable state. In this case, set the
V- pin voltage equal to the VSS voltage or connect a charger to enter the normal condition.
Over-current condition (Detection of Over-current 1, Over-current 2, and Load short-circuiting)
When the condition in which V- pin voltage is equal to or higher than the over-current detection voltage,
condition which caused by the excess of discharging current over a specified value, continues longer than the
overcharge detection delay time in a battery under the normal condition, the T63H0008A turns the discharging
control FET off to stop discharging. This condition is called the over-current condition.
Though the V- and VSS pins are shorted by the RV-S resistor in the IC under the over-current condition,
the V- pin voltage is pulled to the VDD level by the load as long as the load is connected.
The V- pin voltage returns to V SS level when the load is released. The over-current condition returns to the
normal condition when the impedance between the EB+ and EB- pin becomes higher than the automatic
recoverable load resistance (see the equation [1] below), and the IC detects that the V- pin potential is lower
than the over-current 1 detection voltage (VDET3).
Note:
The automatic recoverable load resistance changes depending on the battery voltage and over-current 1detection voltage
settings.
Overcharge condition
When the battery voltage becomes higher than the overcharge detection voltage (VDD) during charging
under the normal condition and the detection continues for the overcharge detection delay time (tVDET1) or
longer, the T63H0008A turns the charging control FET off to stop charging. This condition is called the
overcharge condition. The overcharge condition is released by the following
two cases ((1) and (2)):
(1) When the battery voltage falls below the voltage difference, the overcharge detection voltage (VDET1) -
overcharge detection hysteresis voltage (VHCT1 ), the T63H0008A turns the charging control FET on and
turns to the normal condition.
(2) When a load is connected and discharging starts, the T63H0008A turns the charging control FET on and
returns to the normal condition. The mechanism is : just after the load is connected and discharging starts,
the discharging current flows through the parasitic diode in the charging control FET. At this moment V-
pin potential increases momentarily voltage of the parasitic diode from the VSS level When the V- pin
voltage goes higher than the over-current 1 detection voltage, and provided that the battery voltage goes
相關PDF資料 |
PDF描述 |
|---|---|
| T63H0008A-DX | Li-Ion/Polymer Battery for one-cell Protector |
| T66H0001A | 240 output LCD Segment/Common Driver IC |
| T66H0001A-Y | 240 output LCD Segment/Common Driver IC |
| T66H0002A | 160 output LCD Segment/Common Driver IC |
| T66H0002A-AY | 160 output LCD Segment/Common Driver IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T63H0008A-DX | 制造商:TMT 制造商全稱:TMT 功能描述:Li-Ion/Polymer Battery for one-cell Protector |
| T63XA-100-10-D06 | 制造商:Vishay Roederstein 功能描述:RES TRMR 100 OHM 10% 1/4W 13TURN 1.8MM PIN TH - Rail/Tube |
| T63XA-100K-10-D06 | 制造商:Vishay Roederstein 功能描述:RES TRMR 100K OHM 10% 1/4W 13TURN 1.8MM PIN TH - Rail/Tube |
| T63XA100KT20 | 功能描述:微調電阻 - 通孔 T63 XA 10U 10% TU e3 RoHS:否 制造商:Vishay/Sfernice 產品:Trimmer Resistors - Multi Turn 產品類型:Multiturn 轉數:14 錐度:Linear 電阻:10 kOhms 電壓額定值:250 V 端接類型:Pin 功率額定值:250 mW (1/4 W) 容差:10 % 溫度系數:100 PPM / C |
| T63XA101KT20 | 功能描述:微調電阻 - 通孔 T63 XA 100U 10% TU e3 RoHS:否 制造商:Vishay/Sfernice 產品:Trimmer Resistors - Multi Turn 產品類型:Multiturn 轉數:14 錐度:Linear 電阻:10 kOhms 電壓額定值:250 V 端接類型:Pin 功率額定值:250 mW (1/4 W) 容差:10 % 溫度系數:100 PPM / C |
發布緊急采購，3分鐘左右您將得到回復。