- 您現在的位置：買賣IC網 > PDF目錄1970 > T89C51AC2-SLSIM (Atmel)IC 8051 MCU FLASH 32K 44PLCC PDF資料下載
參數資料
| 型號： | T89C51AC2-SLSIM |
| 廠商： | Atmel |
| 文件頁數： | 67/121頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 8051 MCU FLASH 32K 44PLCC |
| 標準包裝： | 27 |
| 系列： | 89C |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 40MHz |
| 連通性： | UART/USART |
| 外圍設備： | POR，PWM，WDT |
| 輸入/輸出數： | 34 |
| 程序存儲器容量： | 32KB（32K x 8） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 2K x 8 |
| RAM 容量： | 1.25K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 3 V ~ 5.5 V |
| 數據轉換器： | A/D 8x10b |
| 振蕩器型： | 外部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁當前第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁
5
A/T89C51AC2
4127H–8051–02/08
P3.0:7
I/O
Port 3:
Is an 8-bit bi-directional I/O port with internal pull-ups. Port 3 pins that have 1’s written to them are pulled high by the internal
pull-up transistors and can be used as inputs in this state. As inputs, Port 3 pins that are being pulled low externally will be a
source of current (IIL, see section "Electrical Characteristic") because of the internal pull-ups.
The output latch corresponding to a secondary function must be programmed to one for that function to operate (except for
TxD and WR). The secondary functions are assigned to the pins of port 3 as follows:
P3.0/RxD:
Receiver data input (asynchronous) or data input/output (synchronous) of the serial interface
P3.1/TxD:
Transmitter data output (asynchronous) or clock output (synchronous) of the serial interface
P3.2/INT0:
External interrupt 0 input/timer 0 gate control input
P3.3/INT1:
External interrupt 1 input/timer 1 gate control input
P3.4/T0:
Timer 0 counter input
P3.5/T1:
Timer 1 counter input
P3.6/WR:
External Data Memory write strobe; latches the data byte from port 0 into the external data memory
P3.7/RD:
External Data Memory read strobe; Enables the external data memory.
It can drive CMOS inputs without external pull-ups.
P4.0:1
I/O
Port 4:
Is an 2-bit bi-directional I/O port with internal pull-ups. Port 4 pins that have 1’s written to them are pulled high by the internal
pull-ups and can be used as inputs in this state. As inputs, Port 4 pins that are being pulled low externally will be a source of
current (IIL, on the datasheet) because of the internal pull-up transistor.
P4.0
P4.1:
It can drive CMOS inputs without external pull-ups.
RESET
I/O
Reset:
A high level on this pin during two machine cycles while the oscillator is running resets the device. An internal pull-down
resistor to VSS permits power-on reset using only an external capacitor to VCC.
ALE
O
ALE:
An Address Latch Enable output for latching the low byte of the address during accesses to the external memory. The ALE is
activated every 1/6 oscillator periods (1/3 in X2 mode) except during an external data memory access. When instructions are
executed from an internal Flash (EA = 1), ALE generation can be disabled by the software.
PSEN
O
PSEN:
The Program Store Enable output is a control signal that enables the external program memory of the bus during external
fetch operations. It is activated twice each machine cycle during fetches from the external program memory. However, when
executing from of the external program memory two activations of PSEN are skipped during each access to the external Data
memory. The PSEN is not activated for internal fetches.
EA
I
EA:
When External Access is held at the high level, instructions are fetched from the internal Flash when the program counter is
less then 8000H. When held at the low level,A/T89C51AC2 fetches all instructions from the external program memory
.
XTAL1
I
XTAL1:
Input of the inverting oscillator amplifier and input of the internal clock generator circuits.
To drive the device from an external clock source, XTAL1 should be driven, while XTAL2 is left unconnected. To operate
above a frequency of 16 MHz, a duty cycle of 50% should be maintained.
XTAL2
O
XTAL2:
Output from the inverting oscillator amplifier.
Table 1. Pin Description (Continued)
Pin Name
Type
Description
相關PDF資料 |
PDF描述 |
|---|---|
| T89C51CC01UA-7CTIM | IC 8051 MCU FLASH 32K 64BGA |
| T89C51CC02UA-TDSIM | IC 8051 MCU FLASH 16K 24-SOIC |
| TC520ACOE713 | IC SERIAL INTERFACE ADT 16SOIC |
| TC530COI713 | IC DATA ACQ SUBSYSTEM 28SOIC |
| TDA3653B/N2,112 | IC VERT DEFLECT 9-SIL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T89C51AC2-SLSI-M | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit MCU with 32K bytes Flash, 10 bits A/D and EEPROM |
| T89C51AC2-SLTC-M | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit MCU with 32K bytes Flash, 10 bits A/D and EEPROM |
| T89C51AC2-SLTE-M | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit MCU with 32K bytes Flash, 10 bits A/D and EEPROM |
| T89C51AC2-SLTI-M | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit MCU with 32K bytes Flash, 10 bits A/D and EEPROM |
| T89C51CC01 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Enhanced 8-bit Microcontroller with CAN Controller and Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。