- 您現在的位置：買賣IC網 > PDF目錄373542 > TA1395FNG (Toshiba Corporation) Mixer/Oscillator and PLL IC for TV/VCR Tuner PDF資料下載
參數資料
| 型號： | TA1395FNG |
| 廠商： | Toshiba Corporation |
| 英文描述： | Mixer/Oscillator and PLL IC for TV/VCR Tuner |
| 中文描述： | 混頻器/振蕩器和PLL集成電路電視/錄像機調諧器 |
| 文件頁數： | 13/24頁 |
| 文件大小： | 294K |
| 代理商： | TA1395FNG |
TA1395FNG
2005/05/20
13
BYTE 4
Byte 4 is a control byte used to set the different functions. Bit 2 (CP) and controls the output current of the charge-pump
circuit. When bit 2 is set to [0], the output current is set to +55
μ
A; when it is set to [1] , it is +250
μ
A.
Bit 3 (T2), bit 4 (T1), and bit 5 (T0) are used to set charge pump, the phase comparator reference signal output and
counter divider output in test mode. (For details of test mode, see the test mode setting table.)
Bit 6 (Rsa) and bit 7 (Rsb) are used to set the crystal reference frequency divider ratio. (For details of the crystal
reference frequency divider ratio, see the table for crystal reference frequency divider ratios.)
Bit 8 (OS) is used to set the charge-pump driver amplifier output setting. When bit 8 is set to [0], the output is ON (the
normal setting used); when it is set to [1], the output is OFF (charge pump is sink mode).
BYTE 5
Byte 5 is used to set the test mode and control the output ports (BS_V, BS_VH, BS_FM).
When a bandswitch data is set to [0], the output port is OFF; when it is set to [1], it is ON.
Bandswitch setting is also used to switch between the VHF and UHF bands and it is control standby mode.
When the bandswitch data for either B1 or B2 is [1], VHF mode is effective.
When the bandswitch data for both B1 and B2 is [0], UHF mode is effective.
When the bandswitch data for both B1 and B2 is [1], Standby mode is effective.
Set the following maximum values for currents to the bandswitch driver. Ensure also that the total band current is
within 15 mA when two bands are operating at the same time.
BS_V (pin 7) output current: 5 mA (maximum)
BS_VH (pin 8) output current: 10 mA (maximum)
BS_FM (pin 9) output current: 5 mA (maximum)
B) READ MODE (Status Request)
When Read Mode is set, power-on reset operation status and phase comparator lock detector output status are output to
the master device.
Bit 1 (POR) indicates the power-on reset operation status. When the power supply of Vcc stops, this bit is set to [1]. The
conditions for reset to [0] are that voltage supplied to Vcc is 3V or higher, that transmission is requested in READ MODE,
and that the status is output. (When Vcc is turned on, bit 1 is also set to [1].)
Bit 2 (FL) indicates the phase comparator lock status. When this is locked, [1] is output; when it is unlocked, [0] is
output.
相關PDF資料 |
PDF描述 |
|---|---|
| TA2002 | STEREO HEADPHONE AMPLIFIER (3V USE) |
| TA2002F | STEREO HEADPHONE AMPLIFIER (3V USE) |
| TA2003FG | AM / FM Radio IC |
| TA2003PG | AM / FM Radio IC |
| TA2003 | AM/FM RADIO IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TA-14.31818MBD-T | 功能描述:標準時鐘振蕩器 14.31818MHz 3.3V 25 ppm -40C to 85C RoHS:否 制造商:AVX 產品:Standard Clock Oscillators 封裝 / 箱體:7 mm x 5 mm 頻率:75 MHz 頻率穩定性:50 PPM 電源電壓:2.5 V 負載電容: 端接類型:SMD/SMT 最小工作溫度:0 C 最大工作溫度:+ 70 C 輸出格式:LVDS 尺寸: 封裝:Reel 系列: |
| TA-14.31818MBE-T | 制造商:TXC Corporation 功能描述:OSC MEMS 14.31818 MHZ 3.3V SMD |
| TA-14.31818MCD-T | 功能描述:標準時鐘振蕩器 14.31818MHz 2.5V 25ppm -40C to 85C RoHS:否 制造商:AVX 產品:Standard Clock Oscillators 封裝 / 箱體:7 mm x 5 mm 頻率:75 MHz 頻率穩定性:50 PPM 電源電壓:2.5 V 負載電容: 端接類型:SMD/SMT 最小工作溫度:0 C 最大工作溫度:+ 70 C 輸出格式:LVDS 尺寸: 封裝:Reel 系列: |
| TA-14.31818MCE-T | 制造商:TXC Corporation 功能描述:OSC MEMS 14.31818 MHZ 2.5V SMD |
| TA-14.31818MDD-T | 功能描述:標準時鐘振蕩器 14.31818MHz 1.8V 25ppm -40C to 85C RoHS:否 制造商:AVX 產品:Standard Clock Oscillators 封裝 / 箱體:7 mm x 5 mm 頻率:75 MHz 頻率穩定性:50 PPM 電源電壓:2.5 V 負載電容: 端接類型:SMD/SMT 最小工作溫度:0 C 最大工作溫度:+ 70 C 輸出格式:LVDS 尺寸: 封裝:Reel 系列: |
發布緊急采購，3分鐘左右您將得到回復。