- 您現在的位置：買賣IC網 > PDF目錄98163 > TAS5414TDKDRMQ1 (TEXAS INSTRUMENTS INC) 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PDSO36 PDF資料下載
參數資料
| 型號： | TAS5414TDKDRMQ1 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PDSO36 |
| 封裝： | GREEN, PLASTIC, HSSOP-36 |
| 文件頁數： | 31/43頁 |
| 文件大?。?/td> | 978K |
| 代理商： | TAS5414TDKDRMQ1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
www.ti.com
Parallel Operation (PBTL)
DEMODULATION FILTER DESIGN
THERMAL INFORMATION
SLOS514A – FEBRUARY 2007 – REVISED JULY 2007
APPLICATION INFORMATION (continued)
TAS5414 and TAS5424 can be used to drive four 4
loads, two 2 loads, or even one 1 load by paralleling
BTL channels on the load side of the LC output filter. For parallel operation, identical I2C settings are required
for any two paralleled channels (especially gain and current-limit settings) in order to have reliable system
performance and evenly dissipated power on multiple channels. Having identical gain and current-limit settings
can also prevent energy feeding back from one channel to the other. For smooth power up, power down, and
mute operation, the same control commands (such as mute, play, Hi-Z, etc.) should be sent to the paralleled
channels at the same time. Load diagnostic is also supported for parallel connection. Paralleling on the
TAS5414 and TAS5424 side of the LC output filter is not supported, and can result in device failure.
The TAS5414 and TAS5424 amplifier outputs are driven by high-current LDMOS transistors in an H-bridge
configuration. These transistors are either off or fully on. The result is a square-wave output signal with a duty
cycle that is proportional to the amplitude of the audio signal. It is recommended that a second-order LC filter be
used to recover the audio signal. The main purpose of the demodulation filter is to attenuate the high-frequency
components of the output signals that are out of the audio band. Design of the demodulation filter significantly
affects the audio performance of the power amplifier. Therefore, to meet the device THD+N specification, the
selection of the inductors used in the output filter should be carefully considered. The rule is that the inductance
should remain stable within the range of peak current seen at maximum output power and deliver approximately
5
μH of inductance at 16 A. If this rule is observed, the TAS5414 and TAS5424 should not have distortion issues
due to the output inductors. Another parameter to be considered is the idle-current loss in the inductor. This can
be measured or specified as inductor dissipation (D). The target specification for dissipation is less than 0.05. If
the dissipation factor is above this value, idle current increases. In general, 10-
μH inductors suffice for most
applications. The frequency response of the amplifier is slightly altered by the change in output load resistance;
however, unless tight control of frequency response is necessary (better than 0.5 dB), it is not necessary to
deviate from 10
μH.
The thermally augmented package provided with the TAS5414 and TAS5424 is designed to interface directly to
heat sinks using a thermal interface compound (for example, Artic Silver, Ceramique thermal compound.) The
heat sink then absorbs heat from the ICs and couples it to the local air. If louvers or fans are supplied, this
process can reach equilibrium and heat can be continually removed from the ICs. Because of the efficiency of
the TAS5414 and TAS5424, heat sinks can be smaller than those required for linear amplifiers of equivalent
performance.
RθJA is a system thermal resistance from junction to ambient air. As such, it is a system parameter with the
following components:
R
θJC (the thermal resistance from junction to case, or in this case the heat slug)
Thermal grease thermal resistance
Heat sink thermal resistance
The thermal grease thermal resistance can be calculated from the exposed heat slug area and the thermal
grease manufacturer's area thermal resistance (expressed in
°C-in2/W or °C-mm2/W). The area thermal
resistance of the example thermal grease with a 0.001-inch (0.0254-mm) thick layer is about 0.007
°C-in2/W
(4.52
°C-mm2/W). The approximate exposed heat slug size is as follows:
TAS5424, 44-pin PSOP3
…………………. 0.124 in2 (80 mm2)
TAS5414, 36-pin PSOP3
…………………. 0.124 in2 (80 mm2)
Dividing the example thermal grease area resistance by the area of the heat slug gives the actual resistance
through the thermal grease for both parts:
TAS5424, 44-pin PSOP3
………………… 0.40°C/W
TAS5414, 36-pin PSOP3
………………… 0.40°C/W
37
相關PDF資料 |
PDF描述 |
|---|---|
| TAS5414TDKDMQ1G4 | 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PDSO36 |
| TAS5414TDKDRMQ1G4 | 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PDSO36 |
| TAS5504PAGRG4 | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TAS5504PAGG4 | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TAS5508BPAGG4 | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TAS5414TDKDRMQ1G4 | 功能描述:音頻放大器 4-Ch Auto Dig Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5414TDKDRQ1 | 功能描述:音頻放大器 4-Ch Auto Dig Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5414TDKDRQ1G4 | 功能描述:音頻放大器 4-Ch Auto Dig Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5421EVM | 功能描述:EVAL BOARD FOR TAS5421 制造商:texas instruments 系列:- 零件狀態:在售 放大器類型:D 類 輸出類型:1-通道（單聲道） 不同負載時的最大輸出功率 x 通道數:22W x 1 @ 4 歐姆 電壓 - 電源:4.5 V ~ 18 V 板類型:完全填充 使用的 IC/零件:TAS5421 所含物品:板 標準包裝:1 |
| TAS5421QPWPRQ1 | 功能描述:Amplifier IC 1-Channel (Mono) Class D 16-HTSSOP 制造商:texas instruments 系列:汽車級，AEC-Q100 包裝:剪切帶（CT） 零件狀態:有效 類型:D 類 輸出類型:1-通道（單聲道） 不同負載時的最大輸出功率 x 通道數:22W x 1 @ 4 歐姆 電壓 - 電源:4.5 V ~ 18 V 特性:靜音，短路和熱保護 安裝類型:表面貼裝 工作溫度:-40°C ~ 125°C（TA） 供應商器件封裝:16-HTSSOP 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬）裸焊盤 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。