- 您現在的位置：買賣IC網 > PDF目錄98165 > TAS5707PHPR (TEXAS INSTRUMENTS INC) 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 PDF資料下載
參數資料
| 型號： | TAS5707PHPR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| 封裝： | 7 X 7 MM, GREEN, PLASTIC, HTQFP-48 |
| 文件頁數： | 26/57頁 |
| 文件大?。?/td> | 1000K |
| 代理商： | TAS5707PHPR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
2
s
m
2
s
m
2
s
m
AVDD/DVDD
PDN
PVDD
RESET
T0420-01
3V
8V
6V
I S
2
I C
2
2ms
0ns
SLOS556B – NOVEMBER 2008 – REVISED NOVEMBER 2009
www.ti.com
Figure 37. Power Loss Sequence
Recommended Command Sequences
The DAP has two groups of commands. One set is for configuration and is intended for use only during
initialization. The other set has built-in click and pop protection and may be used during normal operation while
audio is streaming. The following supported command sequences illustrate how to initialize, operate, and
shutdown the device.
Initialization Sequence
Use the following sequence to power-up and initialize the device:
1.
Hold all digital inputs low and ramp up AVDD/DVDD to at least 3V.
2.
Initialize digital inputs and PVDD supply as follows:
Drive RESETZ=0, PDNZ=1, and other digital inputs to their desired state while ensuring that
all are never more than 2.5V above AVDD/DVDD. Provide stable and valid I2S clocks
(MCLK, LRCLK, and SCLK). Wait at least 100us, drive RESETZ=1, and wait at least another
13.5ms.
Ramp up PVDD to at least 8V while ensuring that it remains below 6V for at least 100us after
AVDD/DVDD reaches 3V. Then wait at least another 10us.
3.
Trim oscillator (write 0x00 to register 0x1B) and wait at least 50ms.
4.
Configure the DAP via I2C (see Users's Guide for typical values):
Biquads (0x29-36)
DRC parameters (0x3A-3C, 0x40-42, and 0x46)
Bank select (0x50)
5.
Configure remaining registers
6.
Exit shutdown (sequence defined below).
32
Copyright 2008–2009, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TAS5707PHP | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TAS5708PHP | 20.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TAS5708PHPR | 20.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TAS5709AGPHPR | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TAS5709AGPHP | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TAS5708 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:20-W STEREO DIGITAL AUDIO POWER AMPLIFIER WITH EQ/DRC and FEEDBACK |
| TAS5708EVM | 功能描述:音頻 IC 開發工具 TAS5708EVM Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TAS5708PHP | 功能描述:音頻放大器 20W St Closed-Loop I2S In Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5708PHPR | 功能描述:音頻放大器 20W St Closed-Loop I2S In Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5709 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:20-W STEREO DIGITAL AUDIO POWER AMPLIFIER WITH EQ AND DRC |
發布緊急采購，3分鐘左右您將得到回復。