- 您現在的位置：買賣IC網 > PDF目錄98167 > TB6549HQ BRUSH DC MOTOR CONTROLLER, 5 A, ZIP25 PDF資料下載
參數資料
| 型號： | TB6549HQ |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 5 A, ZIP25 |
| 封裝： | 1MM PITCH, HZIP-25 |
| 文件頁數： | 8/22頁 |
| 文件大?。?/td> | 377K |
| 代理商： | TB6549HQ |
TB6549FG/PG/HQ
2010-07-13
16
Typical Application Diagram
Note 1: Connect VCC and P-GND through the power supply capacitor. This capacitor should be as close as possible
to the IC.
Note 2: When connecting the motor pins through the capacitor for reducing noise, connect a resistor to the capacitor
for limiting the charge current. The switching loss increases for PWM control. Therefore, whenever
practicable, avoid connecting the capacitor if PWM control is required.
Note 3: Short-circuit S-GND and P-GND as close to the TB6549 as possible.
Note 4: Connect the capacitor C3 to S-GND.
Note 5: Connect the capacitors C1 and C2 as close to the TB6549 as possible, and the capacitor C1 as close to
S-GND.
Note 6: Pins 4, 5, 12, and 13 of the PG type are connected to the bed of the chip. Therefore expanding the round
area of these pins improves the heat radiation effect.
Usage Precautions
·
Utmost care is necessary in the design of the output, VCC, and GND lines since the IC may be destroyed by
short-circuiting between outputs, air contamination faults, or faults due to improper grounding, or by short-circuiting
between contiguous pins.
·
Be sure to install the IC correctly. The IC may be destroyed if installed wrongly (e.g., in reverse).
TB6549FG: Pins 1, 5, 6, 9, 13, 15, 16, and 19 are not connected.
TB6549HQ: Pins 4, 6, 8, 9, 13, 17, 18, 20, 21, and 22 are not connected.
Microcontroller
Note 2
Note 3
Note 4
Note 6
IN2
IN1
S-GND
OUT1
OUT2
SB
FIN/4,5,12,13,6, 20
TB6549
GND
5 V
VDD
VCC
11/9/14
24V
Note1
PORT1
PORT2
PORT3
P-GND
Vreg
3/2/2
4/3/3
CcpA CcpB CcpC
PWM
20/16/25
PWM
18/15/24
2/1/1
C1
C2
C3
C4
C5
TB6549FG/TB6549PG/TB6549HQ
14/11/16
7/6/10
17/14/23
8/7/11
M
Fuse
10/8/12
12/10/15
Note 5
相關PDF資料 |
PDF描述 |
|---|---|
| TB6551FAG | BRUSHLESS DC MOTOR CONTROLLER, PDSO24 |
| TB6552FL | BRUSH DC MOTOR CONTROLLER, 1 A, PQCC24 |
| TB6552FN | BRUSH DC MOTOR CONTROLLER, 1 A, PDSO16 |
| TB6559FG | BRUSH DC MOTOR CONTROLLER, 2.5 A, PDSO16 |
| TB6560AFG | STEPPER MOTOR CONTROLLER, 2.5 A, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB6549HQ(O) | 功能描述:馬達/運動/點火控制器和驅動器 30V Bridge DRVR 3.5A 1.0 Ohm low RDS RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6549P | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Full-Bridge Driver IC for DC Motors |
| TB6549PG | 功能描述:馬達/運動/點火控制器和驅動器 Bridge Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6549PG(O) | 功能描述:馬達/運動/點火控制器和驅動器 30V PWR Supply 3.5A Full Bridge DRVR PWM RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6551F | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:3-Phase Full-Wave Sine-Wave PWM Brushless Motor Controller |
發布緊急采購，3分鐘左右您將得到回復。