- 您現在的位置：買賣IC網 > PDF目錄98167 > TB6551FAG BRUSHLESS DC MOTOR CONTROLLER, PDSO24 PDF資料下載
參數資料
| 型號： | TB6551FAG |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PDSO24 |
| 封裝： | 0.300 INCH, 1 MM PITCH, PLASTIC, SSOP-24 |
| 文件頁數： | 2/20頁 |
| 文件大?。?/td> | 284K |
| 代理商： | TB6551FAG |
TB6551FG/FAG
2008-12-24
10
Outputting reverse rotation detection signal
The direction of motor rotation is detected for every electrical angle of 360°. (The output is high
immediately after reset.)
The REV terminal increases to a 180° turn-on mode at the time of low.
CW/CCW Pin
Actual Motor Rotating Direction
REV Pin
CW (forward)
Low
Low (CW)
CCW (reverse)
High
CW (forward)
High
High (CCW)
CCW (reverse)
Low
Protecting input pin
1.
Over-current protection (Pin Idc)
When the DC-link-current exceeds the internal reference voltage, gate block protection is performed.
Over-current protection is released for each carrier frequency.
Reference voltage
= 0.5 V (typ.)
2.
Gate block protection (Pin RES)
When the input signal level is Low, the output is turned off; when the signal is High, the output is
restarted.
Abnormalities are detected externally, and the signal is input to the pin RES.
RES Pin
OS Pin
Output Turn-on Signal
(U, V, W, X, Y, Z)
Low
High
Low
High
Low
(When RES
= Low, bootstrap capacitor charging stops.)
3.
Internal protection
Positional signal abnormality protection
When the positional signal is HHH or LLL, the output is turned off; otherwise, the output is
restarted.
Low power supply voltage protection (VCC monitor)
Outside the operating voltage range, the turn-on signal output is kept at high impedance to
prevent damage caused by short-circuiting of power components when the power supply is turned
on or off.
Output at high impedance
Turn-on signal
Power supply
voltage
4.5 V (typ.)
4.0 V (typ.)
GND
VM
VCC
Output at high impedance
Output
相關PDF資料 |
PDF描述 |
|---|---|
| TB6552FL | BRUSH DC MOTOR CONTROLLER, 1 A, PQCC24 |
| TB6552FN | BRUSH DC MOTOR CONTROLLER, 1 A, PDSO16 |
| TB6559FG | BRUSH DC MOTOR CONTROLLER, 2.5 A, PDSO16 |
| TB6560AFG | STEPPER MOTOR CONTROLLER, 2.5 A, PQFP64 |
| TB6560AHQ | STEPPER MOTOR CONTROLLER, 3.5 A, PZFM25 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB6551FAG(O,EL,DRY | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase Full-Wave PWM 6V to 10V 2.6us RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6551FG | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:3-Phase Full-Wave Sine-Wave PWM Brushless Motor Controller |
| TB6551FG(0,EL,DRY) | 制造商:Toshiba America Electronic Components 功能描述:IC MOTOR CONTROLLER PAR 24SSOP |
| TB6551FG(EL,DRY) | 功能描述:馬達/運動/點火控制器和驅動器 Brushless DC Motor Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6551FG(O,EL,DRY) | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase Full-Wave Sine-Wave PWM 12V RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。