- 您現在的位置：買賣IC網 > PDF目錄98170 > TC647VUATR BRUSHLESS DC MOTOR CONTROLLER, PDSO8 PDF資料下載
參數資料
| 型號： | TC647VUATR |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| 封裝： | PLASTIC, MSOP-8 |
| 文件頁數： | 26/28頁 |
| 文件大?。?/td> | 478K |
| 代理商： | TC647VUATR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁
2002 Microchip Technology Inc.
DS21447C-page 7
TC647
4.0
SYSTEM BEHAVIOR
The flowcharts describing the TC647’s behavioral
algorithm are shown in Figure 4-1. They can be
summarized as follows:
4.1
Power-Up
(1) Assuming the device is not being held in shutdown
mode (VMIN > VREL)…
(2) Turn VOUT output on for 32 cycles of the PWM
clock. This ensures that the fan will start from a
dead stop.
(3) During this Start-up Timer, if a fan pulse is
detected, branch to Normal Operation; if none are
received…
(4) Activate the 32-cycle Start-up Timer one more time
and look for fan pulse; if a fan pulse is detected,
proceed to Normal Operation; if none are
received…
(5) Proceed to Fan Fault.
(6) End.
4.2
Normal Operation
Normal Operation is an endless loop which may only
be exited by entering shutdown mode or Fan Fault. The
loop can be thought of as executing at the frequency of
the oscillator and PWM.
(1) Reset the missing pulse detector.
(2) Is TC647 in shutdown? If so…
a. VOUT duty cycle goes to zero.
b. FAULT is disabled.
c. Exit the loop and wait for VMIN > VREL to resume
operation (indistinguishable from Power-up).
(3) Drive VOUT to a duty cycle proportional to greater
of VIN and VMIN on a cycle by cycle basis.
(4) If a fan pulse is detected, branch back to the start
of the loop (1).
(5) If the missing pulse detector times out …
(6) Activate the 3-cycle Diagnostic Timer and look for
pulses; if a fan pulse is detected, branch back to
the start of the loop (1); if none are received…
(7) Activate the 32-cycle Start-up Timer and look for
pulses; if a fan pulse is detected, branch back to
the start of the loop (1); if none are received…
(8) Quit Normal Operation and go to Fan Fault.
(9) End.
4.3
Fan Fault
Fan Fault is an infinite loop wherein the TC647 is
latched in shutdown mode. This mode can only be
released by a reset (i.e., VMIN being brought below
VSHDN, then above VREL, or by power cycling).
(1) While in this state, FAULT is latched on (low) and
the VOUT output is disabled.
(2) A reset sequence applied to the VMIN pin will exit
the loop to Power-up.
(3) End.
相關PDF資料 |
PDF描述 |
|---|---|
| TC647VOART | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC648EOA | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC648VOA | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC649BEPA | BRUSHLESS DC MOTOR CONTROLLER, PDIP8 |
| TC648BEUA | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC648 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Fan Speed Controller with Auto-Shutdown and Over-Temperature Alert |
| TC648_13 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Fan Speed Controller with Auto-Shutdown and Over-Temperature Alert |
| TC648B | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:PWM Fan Speed Controllers With Auto-Shutdown, Fan Restart and FanSense⑩ Technology for Fault Detection |
| TC648BEOA | 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Over-T Alert RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TC648BEOA713 | 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Over-T Alert RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。