參數資料
型號： TC7126ARCLW
元件分類： ADC
英文描述： 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PQCC44
封裝： REVERSE, PLASTIC, LCC-44
文件頁數： 2/26頁
文件大小： 413K
代理商： TC7126ARCLW
TC7126/A
DS21458C-page 10
2006 Microchip Technology Inc.
4.0
ANALOG SECTION
In addition to the basic integrate and de-integrate dual
slope cycles discussed above, the TC7126A design
incorporates an auto-zero cycle. This cycle removes
buffer amplifier, integrator and comparator offset volt-
age error terms from the conversion. A true digital zero
reading results without external adjusting potentiome-
ters. A complete conversion consists of three phases:
1.
Auto-Zero phase
2.
Signal Integrate phase
3.
Reference Integrate phase
4.1
Auto-Zero Phase
During the auto-zero phase, the differential input signal
is disconnected from the circuit by opening internal
analog gates. The internal nodes are shorted to analog
common (ground) to establish a zero input condition.
Additional analog gates close a feedback loop around
the integrator and comparator. This loop permits com-
parator offset voltage error compensation. The voltage
level established on CAZ compensates for device offset
voltages. The auto-zero phase residual is typically
10
μV to 15μV. The auto-zero cycle length is 1000 to
3000 clock periods.
4.2
Signal Integrate Phase
The auto-zero loop is entered and the internal differen-
tial inputs connect to VIN+ and VIN-. The differential
input signal is integrated for a fixed time period. The
TC7126/A signal integration period is 1000 clock
periods or counts. The externally set clock frequency is
divided by four before clocking the internal counters.
The integration time period is:
EQUATION 4-1:
The differential input voltage must be within the device
Common mode range when the converter and mea-
sured system share the same power supply common
(ground). If the converter and measured system do not
share the same power supply common, VIN- should be
tied to analog common.
Polarity is determined at the end of signal integrate
phase. The sign bit is a true polarity indication, in that
signals less than 1LSB are correctly determined. This
allows precision null detection limited only by device
noise and auto-zero residual offsets.
4.3
Reference Integrate Phase
The third phase is reference integrate or de-integrate.
VIN- is internally connected to analog common and
VIN+ is connected across the previously charged refer-
ence capacitor. Circuitry within the chip ensures that
the capacitor will be connected with the correct polarity
to cause the integrator output to return to zero. The
time required for the output to return to zero is propor-
tional to the input signal and is between 0 and 2000
counts. The digital reading displayed is:
EQUATION 4-2:
TSI =
4
FOSC
x 1000
Where: FOSC = external clock frequency.
VIN
VREF
1000
相關PDF資料
PDF描述
TC7126ARCPL 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40
TC7126CPL 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40
TC7126RCKW 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PQFP44
TC7126RCPL 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40
TC7126RIPL 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40
相關代理商/技術參數
參數描述
TC7126ARCPL 功能描述:LCD 驅動器 Low Power RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
TC7126ARIPL 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:3-1/2 Digit Analog-to-Digital Converters
TC7126CKW 功能描述:LCD 驅動器 Low Power RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
TC7126CKW713 功能描述:LCD 驅動器 Low Power RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
TC7126CLW 功能描述:LCD 驅動器 Low Power RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*