參數資料
型號: TC7652CPD
廠商: Microchip Technology
文件頁數: 15/16頁
文件大?。?/td> 0K
描述: IC OPAMP CHOPPER STAB LN 14DIP
標準包裝: 30
放大器類型: 斷路器(零漂移)
電路數: 1
轉換速率: 1 V/µs
增益帶寬積: 400kHz
電流 - 輸入偏壓: 30pA
電壓 - 輸入偏移: 2000µV
電流 - 電源: 1mA
電壓 - 電源,單路/雙路(±): 5 V ~ 16 V,±2.5 V ~ 8 V
工作溫度: 0°C ~ 70°C
安裝類型: 通孔
封裝/外殼: 14-DIP(0.300",7.62mm)
供應商設備封裝: 14-PDIP
包裝: 管件
其它名稱: 158-1024
158-1024-ND
TC7652
DS21464B-page 8
2002 Microchip Technology Inc.
4.6
Pin Compatibility
Where possible, the 8-pin device pinout conforms to
such industry standards as the LM101 and LM741. Null
storing external capacitors connect to Pins 1 and 8,
which are usually for offset null or compensation capac-
itors. Output clamp (Pin 5) is similarly used. For OP05
and OP07 devices, replacement of the offset null
potentiometer (connected between Pins 1 and 8 and
VDD by two capacitors from those pins to VSS) provides
compatibility. Replacing the compensation capacitor
between Pins 1 and 8 by two capacitors to VSS is
required. The same operation (with the removal of any
connection to Pin 5) works for LM101,
A748 and sim-
ilar parts.
Because NC pins provide guarding between input and
other pins, the 14-pin device pinout conforms closely to
the LM108. Because this device does not use any extra
pins and does not provide offset nulling (but requires a
compensation capacitor), some layout changes are
necessary to convert to the TC7652.
4.7
Some Applications
Figures 4-2 and 4-3 show basic inverting and nonin-
verting amplifier circuits using the output clamping cir-
cuit to enhance overload recovery performance. The
only limitations on replacing other op amps with the
TC7652 are supply voltage (±8V maximum) and output
drive capability (10k
load for full swing). Overcome
these limitations with a booster circuit (Figure 4-4) to
combine output capabilities of the LM741 (or other
standard device) with input capabilities of the TC7652.
These two form a composite device, therefore, when
adding the feedback network, the monitor loop gains
stability.
FIGURE 4-2:
NONINVERTING
AMPLIFIER WITH
OPTIONAL CLAMP
FIGURE 4-3:
INVERTING AMPLIFIER
WITH OPTIONAL CLAMP
FIGURE 4-4:
USING 741 TO BOOST
OUTPUT DRIVE
CAPABILITY
Figure 4-5 shows the clamp circuit of a zero offset com-
parator. Because the clamp circuit requires the invert-
ing input to follow the input signal, problems with a
chopper stabilized op amp are avoided. The threshold
input must tolerate the output clamp current
≈VIN/R
without disrupting other parts of the system.
Figure 4-6 shows how the TC7652 can offset null high
slew rate and wideband amplifiers.
Mixing the TC7652 with circuits operating at ±15V
requires a lower supply voltage divider with the TC7660
voltage converter circuit operated "backwards." Figure
4-7 shows an approximate connection.
FIGURE 4-5:
LOW OFFSET
COMPARATOR
TC7652
+
Output
Clamp
Input
0.1F
R2
R1
R3
0.1F
+
Output
Input
R2
R1
Clamp
0.1F
TC7652
+
+
+15V
-15V
-7.5V
0.1
F
In
Out
-7.5V
0.1
F
10k
TC7652
741
TC7652
+
VOUT
Clamp
VIN
0.1F
200k
to 2m
VTH
相關PDF資料
PDF描述
TC913ACPA IC OPAMP DUAL AUTO ZERO 8DIP
TCA0372DWG IC OPAMP DUAL POWER 1A 16SOIC
TDA1348AE 48V FAN 127X127X38MM
TDA1548AG 48V FAN 172X150X50.8MM
TDA1748AG 48V FAN 172X50.8MM
相關代理商/技術參數
參數描述
TC7652IJA 功能描述:運算放大器 - 運放 Low Noise RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
TC7652IJD 功能描述:運算放大器 - 運放 Low Noise RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
TC7660 制造商:MICRO CHIP 功能描述:
TC7660_02 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Charge Pump DC-to-DC Voltage Converter
TC7660CJA 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Charge Pump DC-to-DC Voltage Converter