- 您現在的位置：買賣IC網 > PDF目錄10393 > TC850CPL (Microchip Technology)IC ADC 15BIT FAST 40DIP PDF資料下載
參數資料
| 型號： | TC850CPL |
| 廠商： | Microchip Technology |
| 文件頁數： | 3/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 15BIT FAST 40DIP |
| 標準包裝： | 10 |
| 位數： | 15 |
| 采樣率（每秒）： | 40 |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 電壓電源： | 雙 ± |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 40-DIP（0.600"，15.24mm） |
| 供應商設備封裝： | 40-PDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分，單極 |
2006 Microchip Technology Inc.
DS21479C-page 11
TC850
5.0
PIN DESCRIPTION (ANALOG)
5.1
Differential Inputs (IN+ and IN–)
The analog signal to be measured is applied at the IN+
and IN– inputs. The differential input voltage must be
within the Common mode range of the converter. The
input Common mode range extends from VDD - 1.5V to
VSS +1.5V. Within this Common mode voltage range,
an 80 dB CMRR is typical.
The integrator output also follows the Common mode
voltage. The integrator output must not be allowed to
saturate. A worst-case condition exists, for example,
when a large, positive Common mode voltage, with a
near full scale negative differential input voltage, is
applied. The negative input signal drives the integrator
positive when most of its available swing has been
used up by the positive Common mode voltage. For
applications where maximum Common mode range is
critical, integrator swing can be reduced. The integrator
output can swing within 0.4V of either supply without
loss of linearity.
5.2
Differential Reference (VREF)
The TC850 requires two reference voltage sources in
order to generate the “fast-slow” de-integrate phases.
The main voltage reference (VREF1) is applied between
the REF1+ and REF- pins. The secondary reference
(VREF2) is applied between the REF2+ and REF- pins.
The reference voltage inputs are fully differential and
the reference voltage can be generated anywhere
within the power supply voltage of the converter. How-
ever, to minimize rollover error, especially at high con-
version rates, keep the reference Common mode
voltage (i.e., REF-) near or at the analog common
potential. All voltage reference inputs are high-imped-
ance. Average reference input current is typically only
30 pA.
5.3
Analog Common (ANALOG
COMMON)
Analog common is used as the IN- return during the
zero integrator and de-integrate phases of each con-
version. If IN- is at a different potential than analog
common, a Common mode voltage exists in the sys-
tem. This signal is rejected by the 80dB CMRR of the
converter. However, in most applications, IN- will be set
at a fixed, known voltage (power supply common, for
instance). In this case, analog common should be tied
to the same point so that the Common mode voltage is
eliminated.
相關PDF資料 |
PDF描述 |
|---|---|
| MS3106F18-9S | CONN PLUG 7POS STRAIGHT W/SCKT |
| A3FS | CONN PLUG CORD FMAL 3PIN NICKEL |
| VI-JTK-MY-B1 | CONVERTER MOD DC/DC 40V 50W |
| VI-JTJ-MY-B1 | CONVERTER MOD DC/DC 36V 50W |
| VI-B32-MX-F2 | CONVERTER MOD DC/DC 15V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC850IJL | 功能描述:模數轉換器 - ADC 16 Bit Hi Speed A/D RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TC850ILW | 功能描述:模數轉換器 - ADC 16 Bit Hi Speed A/D RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TC850ILW713 | 功能描述:模數轉換器 - ADC 16 Bit Hi Speed A/D RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TC8521AM | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:REAL TIME CLOCK ケ |
| TC8521AP | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:REAL TIME CLOCK ケ |
發布緊急采購，3分鐘左右您將得到回復。