- 您現在的位置：買賣IC網 > PDF目錄272836 > TCM809SVNB 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 PDF資料下載
參數資料
| 型號： | TCM809SVNB |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| 封裝： | SOT-23B, 3 PIN |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 298K |
| 代理商： | TCM809SVNB |
TCM809/TCM810
DS21661B-page 4
2002 Microchip Technology Inc.
2.0
APPLICATIONS INFORMATION
2.1
VDD Transient Rejection
The TCM809/TCM810 provides accurate VDD monitor-
ing and reset timing during power-up, power-down, and
brownout/sag conditions. These devices also reject
negative-going transients (glitches) on the power sup-
ply line. Figure 2-1 shows the maximum transient dura-
tion vs. maximum negative excursion (overdrive) for
glitch rejection. Any combination of duration and over-
drive which lies under the curve will not generate a
reset signal.
FIGURE 2-1:
Maximum
Transient
Duration
vs.
Overdrive for Glitch Rejection at 25°C.
Combinations above the curve are detected as a
brownout or power-down condition. Transient immunity
can be improved by adding a capacitor in close proxim-
ity to the VDD pin of the TCM809/TCM810.
2.2
RESET Signal Integrity During
Power-Down
The TCM809 RESET output is valid to VDD = 1.0V.
Below this voltage the output becomes an "open cir-
cuit" and does not sink current. This means CMOS
logic inputs to the microcontroller will be floating at an
undetermined voltage. Most digital systems are com-
pletely shutdown well above this voltage. However, in
situations where RESET must be maintained valid to
VDD = 0V, a pull-down resistor must be connected from
RESET to ground to discharge stray capacitances and
hold the output low (Figure 2-2). This resistor value,
though not critical, should be chosen such that it does
not appreciably load RESET under normal operation
(100 k
will be suitable for most applications). Simi-
larly, a pull-up resistor to VDD is required for the
TCM810 to ensure a valid high RESET for VDD below
1.0V.
FIGURE 2-2:
The addition of R1 at the RESET
output of the TCM809 ensures that the RESET output
is valid to VDD = 0V.
Reset Comparator Overdrive
[V
TH - VDD] (mv)
400
240
160
320
80
0
1
5
100
1000
T
A = +25°C
V
TH
Duration
Overdrive
V
DD
TCM8XXL/M/J (SOT-23)
Maxi
m
u
m
T
ran
sien
tD
u
ra
ti
o
n
(
sec
)
TCM8XXZ/R/S/T
(SOT-23)
[V
TH - VDD] (mv)
30
40
50
60
70
80
90
100
110
120
130
1
10
100
1000
Reset Comparator Overdrive (mV)
V
DD
to
Reset
Delay
(
sec)
TCM8XXL/M/J (SC-70)
TCM8XXZ/R/S/T (SC-70)
TCM809
V
DD
V
DD
R1
100 k
RESET
GND
相關PDF資料 |
PDF描述 |
|---|---|
| TRU050GACGA30.72 | PHASE LOCKED LOOP, CDSO16 |
| TRU050GACGB16.128 | PHASE LOCKED LOOP, CDSO16 |
| TRU050GACGB40 | PHASE LOCKED LOOP, CDSO16 |
| TRU050GACHA16.384 | PHASE LOCKED LOOP, CDSO16 |
| TRU050GACHA65.536 | PHASE LOCKED LOOP, CDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TCM809SVNB713 | 功能描述:監控電路 Microprocessor 2.93V RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| TCM809SVNB713-CUT TAPE | 制造商:Microchip 功能描述:TCM809 Series 2.93 V 140 ms 3-Pin Microcontroller Reset Monitor - SOT23B-3 |
| TCM809TEB713 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:3-Pin Microcontroller Reset Monitors |
| TCM809TELB713 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:3-Pin Microcontroller Reset Monitors |
| TCM809TEN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:3-Pin Microcontroller Reset Monitors |
發布緊急采購，3分鐘左右您將得到回復。