參數資料
型號： TDA3602
廠商： NXP SEMICONDUCTORS
元件分類： 模擬信號調理
英文描述： Multiple output voltage regulator(多路輸出電壓穩壓器)
中文描述： SPECIALTY ANALOG CIRCUIT, PSIP9
封裝： PLASTIC, SIP-9
文件頁數： 13/26頁
文件大?。?/td> 205K
代理商： TDA3602
July 1994
13
Philips Semiconductors
Product specification
Multiple output voltage regulator
TDA3602
APPLICATION INFORMATION
Noise
Table 3
Noise at regulator outputs dependent on
capacitive load (C
L
).
Note
1.
Regulators loaded with 100mA; noise in
μ
V RMS
(B = 10 Hz to 1 MHz).
The available noise at the output of the regulators depends
on the bandwidth of the regulators, which can be adjusted
by means of the load capacitors. The noise figures are
given in Table 3.
Although stability is guarenteed when C
L
is higher than
10
μ
F (over temperature range) with tan (
φ
) = 1 in the
frequency range 1 kHz to 20 kHz, it is recommended to
use a 47
μ
F load capacitor for Regulators 1 and 2. When
a microprocessor is supplied by Regulator 3 much noise
can be produced by this microprocessor. This noise is not
influenced by increasing the load capacitor of Regulator 3.
The noise on the supply line depends on the supply
capacitor. When a high frequency capacitor of 220 nF with
an electrolytic capacitor of 100
μ
F in parallel is placed
directly over pin 1 (V
P
) and pin 6 (ground) the noise is
minimized.
The stabilizer is in 'power on' after the supply is
reconnected (V
bu
> 7.9 V) and 0.1 < V
sc
< 2.2 V.
Application circuits
S
TABILIZER WITHOUT MICROPROCESSOR
1
The low end application is illustrated in Fig.7. When switch
SW1 is closed, a pulse is generated at the state control
input by C5 and R1, and the regulator is switched from
power off to the on mode (all three regulators are on). The
HOLD signal can be used to control the mute signal for the
power amplifiers. This signal is HIGH when all the
regulators are in regulation and V
P1
Schmitt trigger is true.
REGULATOR
(NOTE
1
)
C
L
REG
I
L
10
μ
F
800
μ
V
500
μ
V
350
μ
V
47
μ
F
220
μ
V
115
μ
V
190
μ
V
220
μ
F
160
μ
V
1
2
3
150 mA
100 mA
50 mA
S
TABILIZER WITHOUT MICROPROCESSOR
2
Fig.8 illustrates the application circuit for a low end radio
set with push switches when no microprocessor is used.
The stabilizer can be switched to the on mode by pressing
switch SW1. In this mode, Regulators 1 and 2 are switched
on, so transistor T1 takes over from switch SW1. The
stabilizer can only be switched off by connecting the base
of T1 to ground (SW1 not pressed). This can be achieved
by pressing switch SW2.
The hold signal is only HIGH when the device is in the on
mode and both V
P
and the regulators are available, so that
this signal can be used to control the power stages (mute).
During a fault condition, this signal turns LOW
immediately.
When the stabilizer is connected to the supply for the first
time, the initial state will be the power-on stage, so
Regulators 1 and 2 are not switched on.
S
TABILIZER USED WITH MICROPROCESSOR
For a good understanding of the high end application,
shown in Fig.10, consult the flow chart of Fig.9.
When the set is off, a reset can be generated by
connecting the set to the supply for the first time (stabilizer
in power-on), or by pressing any key on the key matrix
(stabilizer in reset mode). When the reset is generated, the
stabilizer is held in the reset mode for a short period by T1.
The microprocessor has to take over control by making
reset mode equal to 0. The microprocessor can then
proceed with the initializing process. After this action, the
microprocessor has to check if the correct key has been
pressed. If so, the radio can be switched on by making on
equal to 0; if not, the microprocessor must switch the
device to the coma mode again, by making reset mode
and on both equal to 1; (wake mode is entered after a short
time constant, determined by R1
×
C7
×
constant), and
switch itself to sleep mode.
When the reset is generated for the first time (power-on
mode), the mode of the device can be detected by the hold
signal. If on = 0 and hold remains LOW, then the
microprocessor is in the power-on mode. In this event, the
microprocessor must go to the switch-off routine (making
on and reset mode both equal to 1).
相關PDF資料
PDF描述
TDA3603 Multiple voltage regulator with switch(帶開關轉換的多路輸出穩壓器)
TDA3604Q Multiple voltage regulators with external reset delay and switch(外部帶有復位延遲和開關轉換的多路輸出電壓穩壓器)
TDA3604TH Multiple voltage regulators with external reset delay and switch(外部帶有復位延遲和開關轉換的多路輸出電壓穩壓器)
TDA3606 Multiple voltage regulator with battery detection(帶電池檢測的多路輸出電壓穩壓器)
TDA3616 Multiple voltage regulator with battery detection(帶電池檢測的多路輸出電壓穩壓器)
相關代理商/技術參數
參數描述
TDA3602/N3,112 功能描述:開關變換器、穩壓器與控制器 MULTI-OUTPUT VOLTAGE RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
TDA3602U 功能描述:開關變換器、穩壓器與控制器 MULTI-OUTPUT VOLTAGE REGULATOR RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
TDA3603 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multiple voltage regulator with switch
TDA3603P 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multiple voltage regulator with switch
TDA3604 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Positive Fixed Voltage Regulator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*