- 您現在的位置：買賣IC網 > PDF目錄368628 > TDA3606 (NXP Semiconductors N.V.) Multiple voltage regulator with battery detection(帶電池檢測的多路輸出電壓穩壓器) PDF資料下載
參數資料
| 型號： | TDA3606 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Multiple voltage regulator with battery detection(帶電池檢測的多路輸出電壓穩壓器) |
| 中文描述： | 多帶電池檢測電壓調節器（帶電池檢測的多路輸出電壓穩壓器） |
| 文件頁數： | 12/16頁 |
| 文件大小： | 95K |
| 代理商： | TDA3606 |
1998 Jun 16
12
Philips Semiconductors
Product specification
Multiple voltage regulator with battery
detection
TDA3606
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(order code 9398 652 90011).
Reflow soldering
Reflow soldering techniques are suitable for all SO
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250
°
C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45
°
C.
Wave soldering
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
The longitudinal axis of the package footprint must be
parallel to the solder flow.
The package footprint must incorporate solder thieves at
the downstream end.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°
C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°
C within
6 seconds. Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°
C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA3616 | Multiple voltage regulator with battery detection(帶電池檢測的多路輸出電壓穩壓器) |
| TDA3617 | Multiple output voltage regulator(多路輸出電壓穩壓器) |
| TDA3618JR | Multiple voltage regulator with switch and ignition buffers(帶開關和點火緩沖器的多路輸出穩壓器) |
| TDA3653B | Vertical deflection and guard circuit(垂直偏轉與防護電路) |
| TDA3653C | Vertical deflection and guard circuit（110）(垂直偏轉與防護電路（90度）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA3606A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multiple voltage regulator with battery detection |
| TDA3606AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multiple voltage regulator with battery detection |
| TDA3606AT/N1 | 功能描述:低壓差穩壓器 - LDO CARRADIO POWER AMPS RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TDA3606AT/N1,112 | 功能描述:低壓差穩壓器 - LDO CARRADIO POWER AMPS RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TDA3606AT/N1,118 | 功能描述:低壓差穩壓器 - LDO CARRADIO POWER AMPS RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。