- 您現在的位置：買賣IC網 > PDF目錄368628 > TDA4858 (NXP SEMICONDUCTORS) Economy Autosync Deflection Controller (EASDC) PDF資料下載
參數資料
| 型號： | TDA4858 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 偏轉 |
| 英文描述： | Economy Autosync Deflection Controller (EASDC) |
| 中文描述： | HORIZ/VERT DEFLECTION IC, PDIP32 |
| 封裝： | 0.400 INCH, PLASTIC, SOT-232-1, SDIP-32 |
| 文件頁數： | 8/44頁 |
| 文件大?。?/td> | 284K |
| 代理商： | TDA4858 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
1997 Oct 27
8
Philips Semiconductors
Product specification
Economy Autosync Deflection Controller
(EASDC)
TDA4858
PLL2 phase detector
The PLL2 phase detector is similar to the PLL1 detector
and compares the line flyback pulse at HFLB (pin 1) with
the oscillator sawtooth voltage. The PLL2 detector thus
compensates for the delay in the external horizontal
deflection circuit by adjusting the phase of the HDRV
(pin 7) output pulse.
The phase between horizontal flyback and horizontal sync
can be controlled at HPOS (pin 30).
If HPLL2 is pulled to ground, horizontal output pulses,
vertical output currents and B+ control driver pulses are
inhibited. This means, HDRV (pin 7), BDRV (pin 6)
VOUT1 (pin 13) and VOUT2 (pin 12) are floating in this
state. PLL2 and the frequency-locked loop are disabled,
and CLBL (pin 16) provides a continuous blanking signal.
This option can be used for soft start, protection and
power-down modes. When the HPLL2 voltage is released
again, an automatic soft start sequence will be performed
(see Fig.15).
The soft start timing is determined by the filter capacitor at
HPLL2 (pin 31), which is charged with an constant current
during soft start. In the beginning the horizontal driver
stage generates very small output pulses. The width of
these pulses increases with the voltage at HPLL2 until the
final duty factor is reached. At this point BDRV (pin 6),
VOUT1 (pin 13) and VOUT2 (pin 12) are re-enabled.
The voltage at HPLL2 continues to rise until PLL2 enters
its normal operating range. The internal charge current is
now disabled. Finally PLL2 and the frequency-locked loop
are enabled, and the continuous blanking at CLBL is
removed.
Horizontal phase adjustment
HPOS (pin 30) provides a linear adjustment of the relative
phase between the horizontal sync and oscillator
sawtooth. Once adjusted, the relative phase remains
constant over the whole frequency range.
Application hint
: HPOS is a current input, which provides
an internal reference voltage while I
HPOS
is in the specified
adjustment current range. By grounding HPOS the
symmetrical control range is forced to its centre value,
therefore the phase between horizontal sync and
horizontal drive pulse is only determined by PLL2.
Output stage for line drive pulses
An open-collector output stage allows direct drive of an
inverting driver transistor because of a low saturation
voltage of 0.3 V at 20 mA. To protect the line deflection
transistor, the output stage is disabled (floating) for low
supply voltage at V
CC
(see Fig.14).
The duty factor of line drive pulses is slightly dependent on
the actual line frequency. This ensures optimum drive
conditions over the whole frequency range.
X-ray protection
The X-ray protection input XRAY (pin 2) provides a voltage
detector with a precise threshold. If the input voltage at
XRAY exceeds this threshold for a certain time, an internal
latch switches the IC into protection mode. In this mode
several pins are forced into defined states:
Horizontal output stage (HDRV) is floating
B+ control driver stage (BDRV) is floating
Vertical output stages (VOUT1 and VOUT2) are floating
CLBL provides a continuous blanking signal
The capacitor connected to HPLL2 (pin 31) is
discharged.
To reset the latch and return to normal operation, V
CC
has
to be temporarily switched off.
Vertical oscillator and amplitude control
This stage is designed for fast stabilization of vertical
amplitude after changes in sync frequency conditions.
The free-running frequency f
osc(V)
is determined by the
resistor R
VREF
connected to pin 23 and the capacitor
C
VCAP
connected to pin 24. The value of R
VREF
is not only
optimized for noise and linearity performance in the whole
vertical and EW section, but also influences several
internal references. Therefore the value of R
VREF
must not
be changed. Capacitor C
VCAP
should be used to select the
free-running frequency of the vertical oscillator in
accordance with the following formula:
10.8
R
VREF
C
VCAP
To achieve a stabilized amplitude the free-running
frequency f
osc(V)
, without adjustment, should be at least
10% lower than the minimum trigger frequency.
The contributions shown in Table 2 can be assumed.
f
osc V
×
×
---------------------------1
=
相關PDF資料 |
PDF描述 |
|---|---|
| TDA5146T | 1.2UF/630VDC METAL POLY CAP |
| TDA5153AG | Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads |
| TDA5153 | Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads |
| TDA5153X | Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads |
| TDA5153BG | Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA4860 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Vertical deflection power amplifier for monitors |
| TDA4861 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Vertical deflection power amplifier for monitors |
| TDA4862 | 功能描述:功率因數校正 IC BOOST CONTROLLER FOR HI PWR FACTOR/LW THD RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| TDA4862G | 制造商:Infineon Technologies AG 功能描述:Power Factor Correction CONTRLR 8-Pin DSO 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TDA4862G GEG | 功能描述:功率因數校正 IC POWER-FACTOR CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。