- 您現在的位置：買賣IC網 > PDF目錄368629 > TDA6651TT (NXP Semiconductors N.V.) 5 V mixer/oscillator and low noise PLL synthesizer for hybrid terrestrial tuner (digital and analog) PDF資料下載
參數資料
| 型號： | TDA6651TT |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 5 V mixer/oscillator and low noise PLL synthesizer for hybrid terrestrial tuner (digital and analog) |
| 中文描述： | 5伏混頻器/振蕩器，低噪聲的混合型地面調諧器鎖相環頻率合成器（數字和模擬） |
| 文件頁數： | 48/55頁 |
| 文件大?。?/td> | 377K |
| 代理商： | TDA6651TT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
2004 Mar 22
48
Philips Semiconductors
Product specification
5 V mixer/oscillator and low noise PLL synthesizer
for hybrid terrestrial tuner (digital and analog)
TDA6650TT;
TDA6651TT
14 APPLICATION AND TEST INFORMATION
14.1
Tuning amplifier
The tuning amplifier is capable of driving the varicap
voltage without an external transistor. The tuning voltage
output must be connected to an external load of 15 k
which is connected to the tuning voltage supply rail. The
loop filter design depends on the oscillator characteristics
and the selected reference frequency as well as the
required PLL loop bandwidth.
Applications with the TDA6650TT; TDA6651TT have a
largeloopbandwidth,intheorderofafewtensof kHz.The
calculation of the loop filter elements has to be done for
each application, it depends on the reference frequency
and charge pump current. A simulation of the loop can
easily be done using the SIMPATA software from Philips.
14.2
Crystal oscillator
The TDA6650TT; TDA6651TT needs to be used with a
4 MHz crystal in series with a capacitor with a typical value
of 18 pF, connected between pin XTAL1 and pin XTAL2.
Philips crystal 4322 143 04093 is recommended. When
choosing a crystal, take care to select a crystal able to
withstand the drive level of the TDA6650TT; TDA6651TT
without suffering from accelerated ageing. For optimum
performances, it is highly recommended to connect the
4 MHz crystal without any serial resistance.
The crystal oscillator of the TDA6650TT; TDA6651TT
should not be driven (forced) from an external signal.
Do not use the signal on pins XTAL1 or XTAL2, or the
signal present on the crystal, to drive an external IC or for
any other use as this may dramatically degrade the phase
noise performance of the TDA6650TT; TDA6651TT.
14.3
Examples of I
2
C-bus program sequences
Tables 16 to 23 show various sequences where:
S = START
A = acknowledge
P = STOP.
The following conditions apply:
LO frequency is 800 MHz
f
comp
= 166.666 kHz
N = 4800
BS3 output port is on and all other ports are off: thus the
high band is selected
Charge pump current I
CP
= 280
μ
A
Normal mode, with XTOUT buffer on
I
AGC
= 220 nA
AGC take-over point is set to 112 dB
μ
V (p-p)
Address selection is adjusted to make address C2 valid.
To fully program the device, either sequence of Table 16
or 17 can be used, while other arrangements of the bytes
are also possible.
Table 16
Complete sequence 1
Notes
1.
2.
Control byte 1 with bit T/A = 1, to program test bits T2, T1 and T0 and reference divider ratio bits R2, R1 and R0.
Control byte 1 with bit T/A = 0, to program AGC time constant bit ATC and AGC take-over point bits AL2, AL1
and AL0.
Table 17
Complete sequence 2
Notes
1.
2.
Control byte 1 with bit T/A = 1, to program test bits T2, T1 and T0 and reference divider ratio bits R2, R1 and R0.
Control byte 1 with bit T/A = 0, to program AGC time constant bit ATC and AGC take-over point bits AL2, AL1
and AL0.
START
ADDRESS
BYTE
C2
DIVIDER
BYTE 1
12
DIVIDER
BYTE 2
C0
CONTROL
BYTE 1
(1)
CA
CONTROL
BYTE 2
A4
CONTROL
BYTE 1
(2)
84
STOP
S
A
A
A
A
A
A
P
START
ADDRESS
BYTE
C2
CONTROL
BYTE 1
(1)
CA
CONTROL
BYTE 2
A4
DIVIDER
BYTE 1
12
DIVIDER
BYTE 2
C0
CONTROL
BYTE 1
(2)
84
STOP
S
A
A
A
A
A
A
P
相關PDF資料 |
PDF描述 |
|---|---|
| TDA6800 | Video modulator circuit |
| TDA6800T | Video modulator circuit |
| TDA7056 | 3 W mono BTL audio output amplifier(3W單聲道BTL音頻輸出放大器) |
| TDA7057Q | 2 x 8W stereo BTL audio output amplifier with DC volume control(帶DC音量控制的2x8W立體聲BTL音頻輸出放大器) |
| TDA7057A | 50 AMP LATCHING POWER RELAY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA6651TT/C3 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V mixer/oscillator and low noise PLL synthesizer for hybrid terrestrial tuner (digital and analog) |
| TDA6651TT/C3,118 | 功能描述:射頻混合器 Mixer/Oscillator 38-Pin RoHS:否 制造商:NXP Semiconductors 頻率范圍: 轉換損失——最大: 工作電源電壓:6 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| TDA6651TT/C3/S2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V mixer/oscillator and low noise PLL synthesizer for hybrid terrestrial tuner (digital and analog) |
| TDA6651TT/C3/S3 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V mixer/oscillator and low noise PLL synthesizer for hybrid terrestrial tuner (digital and analog) |
| TDA6800 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Video modulator circuit |
發布緊急采購，3分鐘左右您將得到回復。