- 您現在的位置：買賣IC網 > PDF目錄368629 > TDA7057AQ (NXP SEMICONDUCTORS) 2 x 8 W stereo BTL audio output amplifier with DC volume control PDF資料下載
參數資料
| 型號： | TDA7057AQ |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 音頻控制 |
| 英文描述： | 2 x 8 W stereo BTL audio output amplifier with DC volume control |
| 中文描述： | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PZFM13 |
| 封裝： | PLASTIC, SOT-141, SIP-13 |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 116K |
| 代理商： | TDA7057AQ |
1998 Apr 07
9
Philips Semiconductors
Product specification
2
×
8 W stereo BTL audio output amplifier
with DC volume control
TDA7057AQ
Fig.11 Input signal handling.
THD = 1 %.
handbook, halfpage
Vin
(V)
1.6
0
20
VP (V)
0
0.4
MBG665
0.8
1.2
4
8
12
16
Fig.12 Volume control current as a function of
volume control voltage.
handbook, halfpage
(
μ
A)
0
2.0
VVC (V)
10
20
30
20
10
0
MBG666
0.4
0.8
1.2
1.6
APPLICATION INFORMATION
The application diagram is illustrated in Fig.13.
Test conditions
T
amb
= 25
°
C unless otherwise specified; V
P
= 12 V;
V
DC
= 1.4 V; f
i
= 1 kHz; R
L
= 16
.
The quiescent current has been measured without load
impedance.
The output power as a function of the supply voltage has
been measured at THD = 10%. The maximum output
power is limited by the maximum power dissipation and the
maximum available output current.
The maximum input signal voltage is measured at
THD = 1% at the output with a voltage gain of 0 dB.
To avoid instabilities and too high a distortion, the input
ground and power ground must be separated as far as
possible and connected as close as possible to the IC.
The DC volume control can be applied in several ways.
Two possible circuits are shown below the main
application diagram. The circuits at the control pin will
influence the switch-on and switch-off behaviour and the
maximum voltage gain.
For single-end applications the output peak current must
not exceed 100 mA. At higher output currents the
short-circuit protection (MCL) will be active.
Thermal considerations:
At high junction temperatures (>125
°
C) the voltage gain
will decrease when it is higher than 0 dB. This results in a
decrease of the output voltage and an increase of the
distortion level. Thus for an optimal performance of the IC
the heatsink has to be designed properly.
Calculation example for application: V
P
= 15 V; R
L
= 8
,
stereo sine wave; worst case sine wave power dissipation
is 12 W.
For T
amb(max)
= 40
°
C the thermal resistance from junction
40
–
12
to ambient
The thermal resistance of the heatsink becomes:
R
th h-a
= R
th j-a
(R
th j-c
+ R
th c-h
);
R
th h-a
= 7.1
(4 + 0.1) = 3 K/W.
It should be noted that for ‘music power’ the power
dissipation will be approximately half of the sine wave
dissipation. Thus a smaller heatsink can be used.
R
th j-a
)
--125
7.1 K/W
=
=
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8043 | ECONOLINE: RB & RA - Dual Output from a Single Input Rail- Power Sharing on Output- Industry Standard Pinout- 1kVDC & 2kVDC Isolation- Custom Solutions Available- UL94V-0 Package Material- Efficiency to 85% |
| TDA8043H | Satellite Demodulator and Decoder SDD |
| TDA8044 | Satellite demodulator and decoder |
| TDA8044A | Satellite demodulator and decoder |
| TDA8044AH | Satellite demodulator and decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA7057AQ/N2 | 制造商:NXP Semiconductors 功能描述:AMP 2 X 8W BTL VOLT CTRL DBS13P |
| TDA7057AQ/N2,112 | 功能描述:音頻放大器 STER 7712 AMP 2X8W 13DIL RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA7057Q | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2 x 3 W stereo BTL audio output amplifier |
| TDA7072 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single BTL power driver |
| TDA7072A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single BTL power driver |
發布緊急采購，3分鐘左右您將得到回復。