- 您現在的位置：買賣IC網 > PDF目錄98196 > TDA7461ND (STMICROELECTRONICS) SPECIALTY CONSUMER CIRCUIT, PDSO28 PDF資料下載
參數資料
| 型號： | TDA7461ND |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO28 |
| 封裝： | SOP-28 |
| 文件頁數： | 24/48頁 |
| 文件大?。?/td> | 437K |
| 代理商： | TDA7461ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Stereo decoder part
TDA7461
4.6.1
Trigger path
The incoming MPX signal is highpass filtered, amplified and rectified. This second order
highpass-filter has a corner frequency of 140 kHz. The rectified signal, RECT, is lowpass
filtered to generate a signal called PEAK. Also noise with a frequency 140 kHz increases the
PEAK voltage. The PEAK voltage is fed to a threshold generator, which adds to the PEAK
voltage a DC dependent threshold VTH. Both signals, RECT and PEAK+VTH are fed to a
comparator which triggers a re-triggerable monoflop. The monoflop’s output activates the
sample-and-hold circuits in the signalpath for 40 s.
The block diagram of the noiseblanker is given in Figure 25.
4.6.2
Automatic noise controlled threshold adjustment (ATC)
There are mainly two independent possibilities for programming the trigger threshold:
the low threshold in 8 steps (bits D0 to D2 of the noiseblanker byte)
the noise adjusted threshold in 4 steps (bits D3 and D4 of the noiseblanker byte, see fig.
18).
The low threshold is active in combination with a good MPX signal without any noise; the
PEAK voltage is less than 1V. The sensitivity in this operation is high.
If the MPX signal is noisy the PEAK voltage increases due to the higher noise, which is also
rectified. With increasing of the PEAK voltage the trigger threshold increases, too. This
particular gain is programmable in 4 steps (see Figure 17).
Figure 25.
Block diagram of the noiseblankert
4.6.3
Automatic threshold control
Besides the noise controlled threshold adjustment there is an additional possibility for
influencing the trigger threshold. It is depending on the stereo blend control.
The point where the MPX signal starts to become noisy is fixed by the RF part. Therefore
also the starting point of the normal noise-controlled trigger adjustment is fixed (Figure 19).
In some cases the behavior of the noise blanker can be improved by increasing the
threshold even in a region of higher fieldstrength. Sometimes a wrong triggering occurs for
the MPX signal often shows distortion in this range which can be avoided even if using a low
threshold.
+
-
RECTIFIER
LOWPASS
RECT
+
THRESHOLD
GENERATOR
VTH
PEAK
ADDITIONAL
THRESHOLD
CONTROL
MONOFLOP
HOLDN
MPX
D98AU861
HIGH PASS
相關PDF資料 |
PDF描述 |
|---|---|
| TDA7461NDTR | SPECIALTY CONSUMER CIRCUIT, PDSO28 |
| TDA7461N | SPECIALTY CONSUMER CIRCUIT, PDIP28 |
| TDA7462D | SPECIALTY CONSUMER CIRCUIT, PDSO28 |
| TDA7463AD | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO20 |
| TDA7463A | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA7461NDTR | 功能描述:音頻 DSP CAR RADIO SIGNAL RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
| TDA7462 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DUAL AUDIOPROCESSOR WITH COMPANDER AND SUBWOOFER OUTPUT |
| TDA7462D | 功能描述:音頻 DSP Dual Audioprocessor RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
| TDA7462D013TR | 功能描述:音頻 DSP DUAL AUDIOPROCESSOR COMPANDER /SUBWOOFER RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
| TDA7463A | 功能描述:多媒體雜項 Lo Vltg TONE CONTROL RoHS:否 制造商:Texas Instruments 類型: 通道數量: 轉換速率:540 Mbps 分辨率: 封裝 / 箱體:SOIC-16 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。