- 您現在的位置：買賣IC網 > PDF目錄373626 > TDA8589AJ (NXP SEMICONDUCTORS) I2C-bus controlled 4 45 Watt power amplifier and multiple voltage regulator PDF資料下載
參數資料
| 型號： | TDA8589AJ |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | I2C-bus controlled 4 45 Watt power amplifier and multiple voltage regulator |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PZFM37 |
| 封裝： | PLASTIC, SOT725-1, 37 PIN |
| 文件頁數： | 9/55頁 |
| 文件大小： | 561K |
| 代理商： | TDA8589AJ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
2004 Feb 24
9
Philips Semiconductors
Product speci
cation
I
2
C-bus controlled 4 45 Watt power
ampli
er and multiple voltage regulator
TDA8589J; TDA8589xJ
compared with a reference voltage. If the output voltage of
a channel is greater than the reference voltage, bit D2 of
the associated data byte is set and read by the
microcontroller during a read instruction. Note that the
value of this bit is only meaningful when there is no input
signal and the amplifier is not muted. Offset detection is
always enabled.
Speaker protection
If one side of a speaker is connected to ground, a missing
current protection is implemented to prevent damage to
the speaker. A fault condition is detected in a channel
whenthere isa mismatchbetween the powercurrentinthe
high side and the power current in the low side; during a
fault condition the channel will be switched off.
The load status of each channel can be read via the
I
2
C-bus: short to ground (one side of the speaker
connected to ground), short to V
P
(one side of the speaker
connected to V
P
), and shorted load.
Line driver mode
An amplifier can be used as a line driver by switching it to
low gain mode. In normal mode, the gain between
single-ended input and differential output (across the load)
is 26 dB. In low gain mode the gain between single-ended
input and differential output is 20 dB.
Input and AC ground capacitor values
The negative inputs to all four amplifier channels are
combined at pin ACGND. To obtain the best performance
for supply voltage ripple rejection and unwanted audible
noise, the value of the capacitor connected to pin ACGND
must be as close as possible to 4 times the value of the
input capacitor connected to the positive input of each
channel.
Load detection
DC-
LOAD DETECTION
When DC-load detection is enabled, during the start-up
cycle, aDC-offset isapplied slowly to the amplifieroutputs,
and the outputcurrents are measured. If the output current
of an amplifier rises above a certain level, it is assumed
that there is a load of less than 6
the associated data byte register to indicate that a load is
detected.
and bit D5 is reset in
Because the offset is measured during the amplifier
start-up cycle, detection is inaudible and can be performed
every time the amplifier is switched on.
AC-
LOAD DETECTION
AC-load detection can be used to detect that AC-coupled
speakers are connected correctly during assembly. This
requires at least 3 periods of a 19 kHz sine wave to be
applied to the amplifier inputs. The amplifier produces a
peak output voltage which also generates a peak output
current through the AC-coupled speaker. The 19 kHz sine
wave is also audible during the test. If the amplifier detects
three current peaks that are greater than 550 mA, the
AC-load detection bit D1 of instruction byte IB1 is set to
logic 1. Three current peaks are counted to avoid false
AC-load detection which can occur if the input signal is
switched onandoff. The peakcurrent countercan bereset
by setting bit D1 of instruction byte IB1 to logic 0.
To guarantee AC-load detection, an amplifier current of
more than 550 mA is required. AC-load detection will
never occur with a current of less than 150 mA. Figure 3
shows which AC loads are detected at different output
voltages. For example, if a load is detected at an output
voltage of 2.5 V peak, the load is less than 4
is detected, the output impedance is more than 14
. If no load
.
L
OAD DETECTION PROCEDURE
1.
At start-up, enable the AC- or DC-load detection by
setting D1 of instruction byte 1 to logic 1.
10
10
2
Z
o(load)
( )
1
V
o(peak)
(V)
0
10
7.5
2.5
5
(2)
(1)
no load present
load present
undefined
Fig.3
Tolerance of AC-load detection as a
function of output voltage.
(1) I
O(peak)
= < 150 mA.
(2) I
O(peak)
= > 550 mA.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8589BJ | I2C-bus controlled 4 45 Watt power amplifier and multiple voltage regulator |
| TDA8589J | I2C-bus controlled 4 45 Watt power amplifier and multiple voltage regulator |
| TDA8742H | Satellite sound circuit with noise reduction |
| TDA8922B | 2 X 50 W class-D power amplifier |
| TDA9102CT | H/V PROCESSOR FOR TTL V.D.U |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8589AJ/N3 | 功能描述:音頻放大器 POWER AMPL + STABI RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8589AJ/N3,112 | 功能描述:音頻放大器 POWER AMPL + STABI RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8589BJ | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:I2C-bus controlled 4 45 Watt power amplifier and multiple voltage regulator |
| TDA8589BJ/N3 | 功能描述:音頻放大器 POWER AMPL + STABI RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8589BJ/N3,112 | 功能描述:音頻放大器 POWER AMPL + STABI RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。