- 您現在的位置：買賣IC網 > PDF目錄371183 > TDA8846 (NXP Semiconductors N.V.) I2C-bus controlled PAL/NTSC/SECAM TV processors PDF資料下載
參數資料
| 型號： | TDA8846 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | I2C-bus controlled PAL/NTSC/SECAM TV processors |
| 中文描述： | I2C總線控制的PAL / NTSC制式/ SECAM電視處理器 |
| 文件頁數： | 66/68頁 |
| 文件大?。?/td> | 316K |
| 代理商： | TDA8846 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁當前第66頁第67頁第68頁
December 16, 1997
66
Philips Semiconductors
Tentative Device Specification
I
2
C-bus controlled PAL/NTSC/SECAM TV
processors
TDA884X/5X-N2 series
SOLDERING
Plastic dual in-line packages
B
Y DIP OR WAVE
The maximum permissible temperature of the solder is
260
°
C; this temperature must not be in contact with the
joint for more than 5 s. The total contact time of successive
solder waves must not exceed 5 s.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified storage maximum. If the printed-circuit board has
been pre-heated, forced cooling may be necessary
immediately after soldering to keep the temperature within
the permissible limit.
R
EPAIRING SOLDERED JOINTS
Apply a low voltage soldering iron below the seating plane
(or not more than 2 mm above it). If its temperature is
below 300
°
C, it must not be in contact for more than 10 s;
if between 300 and 400
°
C, for not more than 5 s.
Plastic quad flat-packs
B
Y WAVE
During placement and before soldering, the component
must be fixed with a droplet of adhesive. After curing the
adhesive, the component can be soldered. The adhesive
can be applied by screen printing, pin transfer or syringe
dispensing.
Maximum permissible solder temperature is 260
°
C, and
maximum duration of package immersion in solder bath is
10 s, if allowed to cool to less than 150
°
C within 6 s.
Typical dwell time is 4 s at 250
°
C.
A modified wave soldering technique is recommended
using two solder waves (dual-wave), in which a turbulent
wave with high upward pressure is followed by a smooth
laminar wave. Using a mildly-activated flux eliminates the
need for removal of corrosive residues in most
applications.
B
Y SOLDER PASTE REFLOW
Reflow soldering requires the solder paste (a suspension
of fine solder particles, flux and binding agent) to be
applied to the substrate by screen printing, stencilling or
pressure-syringe dispensing before device placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt, infrared, and
vapour-phase reflow. Dwell times vary between 50 and
300 s according to method. Typical reflow temperatures
range from 215 to 250
°
C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 min at 45
°
C.
R
EPAIRING SOLDERED JOINTS
(
BY HAND
-
HELD SOLDERING
IRON OR PULSE
-
HEATED SOLDER TOOL
)
Fix the component by first soldering two, diagonally
opposite, end pins. Apply the heating tool to the flat part of
the pin only. Contact time must be limited to 10 s at up to
300
°
C. When using proper tools, all other pins can be
soldered in one operation within 2 to 5 s at between 270
and 320
°
C. (Pulse-heated soldering is not recommended
for SO packages.)
For pulse-heated solder tool (resistance) soldering of VSO
packages, solder is applied to the substrate by dipping or
by an extra thick tin/lead plating before package
placement.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8846A | I2C-bus controlled PAL/NTSC/SECAM TV processors |
| TDA8847 | I2C-bus controlled PAL/NTSC/SECAM TV processors |
| TDA884X | I2C-bus controlled PAL/NTSC/SECAM TV processors |
| TDA8854H | I2C-bus controlled PAL/NTSC/SECAM TV processors |
| TDA8857H | I2C-bus controlled PAL/NTSC/SECAM TV processors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8846A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:I2C-bus controlled PAL/NTSC/SECAM TV processors |
| TDA8846-N2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:I2C-bus controlled PAL/NTSC/SECAM TV processors |
| TDA8847 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:I2C-bus controlled PAL/NTSC/SECAM TV processors |
| TDA8847-N2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:I2C-bus controlled PAL/NTSC/SECAM TV processors |
| TDA884X | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:I2C-bus controlled PAL/NTSC/SECAM TV processors |
發布緊急采購，3分鐘左右您將得到回復。