- 您現在的位置：買賣IC網 > PDF目錄272328 > TDA8933BTW (NXP SEMICONDUCTORS) Class D Audio Amplifier PDF資料下載
參數資料
| 型號： | TDA8933BTW |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | Class D Audio Amplifier |
| 中文描述： | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
| 封裝： | 6.10 MM, 0.65 MM PITCH, PLASTIC, SOT-249-1, HTSSOP-32 |
| 文件頁數： | 39/42頁 |
| 文件大小： | 245K |
| 代理商： | TDA8933BTW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁
TDA8933B_1
NXP B.V. 2008. All rights reserved.
Preliminary data sheet
Rev. 01 — 23 October 2008
6 of 42
NXP Semiconductors
TDA8933B
Class D audio amplier
8.2 Mode selection and interfacing
The TDA8933B can be switched to one of four operating modes using pins POWERUP
and ENGAGE:
Sleep mode: with low supply current.
Mute mode: the ampliers are switching to idle (50 % duty cycle), but the audio signal
at the output is suppressed by disabling the Vl-converter input stages. The capacitors
on pins HVP1 and HVP2 have been charged to half the supply voltage (asymmetrical
supply only)
Operating mode: the ampliers are fully operational with an output signal
Fault mode
Both pins POWERUP and ENGAGE refer to pin CGND.
Table 4 shows the different modes as a function of the voltages on the POWERUP and
ENGAGE pins.
[1]
When there are symmetrical supply conditions, the voltage applied to pins POWERUP and ENGAGE must
never exceed the supply voltage (VDDA, VDDP1 or VDDP2).
If the transition between Mute mode and Operating mode is controlled via a time constant,
the start-up will be pop-free since the DC output offset voltage is applied gradually to the
output. The bias current setting of the V/I-converters is related to the voltage on pin
ENGAGE.
Mute mode: the bias current setting of the V/I-converters is zero (V/I-converters
disabled).
Operating mode: the bias current is at maximum.
The time constant required to apply the DC output offset voltage gradually between Mute
mode and Operating mode can be generated by applying a capacitor on pin ENGAGE.
The value of the capacitor on pin ENGAGE should be 470 nF.
Table 4.
Mode selection for the TDA8933B
Mode
Pin
POWERUP[1]
ENGAGE[1]
DIAG
Sleep
< 0.8 V
undened
Mute
2 V to 6 V
< 0.8 V
> 2 V
Operating
2 V to 6 V
2.4 V to 6 V
> 2 V
Fault
2 V to 6 V
undened
< 0.8 V
相關PDF資料 |
PDF描述 |
|---|---|
| TSC80C51CXXX-16CXB | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, UUC40 |
| TSC80C51CXXX-16MXP883 | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, UUC40 |
| TSC87C52-25MG | 8-BIT, OTPROM, 25 MHz, MICROCONTROLLER, CDIP40 |
| TSB43DA42AZHCR | PCI BUS CONTROLLER, PBGA196 |
| T80C31-30D | 8-BIT, 30 MHz, MICROCONTROLLER, PQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8933BTW/N2,112 | 功能描述:音頻放大器 Class D audio amplifier 32 leads RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8933BTW/N2,118 | 功能描述:音頻放大器 Class D audio amplifier 32 leads RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8933BTW/N2,512 | 功能描述:音頻放大器 TDA8933BTW/HTSSOP32/TUBEDP//N2 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8933BTW/N2,518 | 功能描述:音頻放大器 TDA8933BTW/HTSSOP32/REEL13DP// RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8933T | 功能描述:音頻放大器 2X10W BTL CLASS D AMP+VOLCTRL RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。