參數資料
型號: TDF5140
廠商: NXP Semiconductors N.V.
英文描述: Brushless DC motor drive circuit
中文描述: 無刷直流電動機驅動電路
文件頁數: 13/19頁
文件大?。?/td> 120K
代理商: TDF5140
1999 March 15
13
Philips Semiconductors
Product specification
Brushless DC motor drive circuit
TDF5140A
Fig.6 CAP-CD and CAP-DC typical voltage waveforms in normal running mode.
handbook, full pagewidth
MGH317
voltage
on CAP-CD
voltage
on CAP-DC
t
T
HE TIMING CAPACITOR
(CAP-TI)
Capacitor CAP-TI is used for timing the successive steps
within one commutation period; these steps include some
internal delays.
The most important function is the watchdog time in which
the motor EMF has to recover from a negative diode-pulse
back to a positive EMF voltage (or vice versa). A watchdog
timer is a guarding function that only becomes active when
the expected event does not occur within a predetermined
time.
The EMF usually recovers within a short time if the motor
is running normally (
<<
ms). However, if the motor is
motionless or rotating in the reverse direction, then the
time can be longer (
>>
ms).
A watchdog time must be chosen so that it is long enough
for a motor without EMF (still) and eddy currents that may
stretch the voltage in a motor winding; however, it must be
short enough to detect reverse rotation. If the watchdog
time is made too long, then the motor may run in the wrong
direction (with little torque).
The capacitor is charged, with a current of 57
μ
A, from
0.2 to 0.3 V. Above this level it is charged, with a current of
5
μ
A, up to 2.2 V only if the selected motor EMF remains
in the wrong polarity (watchdog function). At the end, or, if
the motor voltage becomes positive, the capacitor is
discharged with a current of 28
μ
A. The watchdog time is
the time taken to charge the capacitor, with a current of
5
μ
A, from 0.3 to 2.2 V.
To ensure that the internal delays are covered CAP-TI
must have a minimum value of 2 nF. For the watchdog
function a value for CAP-TI of 10 nF is recommended.
To ensure a good start-up and commutation, care must be
taken that no oscillations occur at the trailing edge of the
flyback pulse. Snubber networks at the outputs should be
critically damped.
Typical voltage waveforms are illustrated by Fig.7.
相關PDF資料
PDF描述
TDF5140A Brushless DC motor drive circuit
TDF5242 Brushless DC motor drive circuit
TDF5242T Brushless DC motor drive circuit
TDF8704 8-bit high-speed analog-to-digital converter
TDF8704T 8-bit high-speed analog-to-digital converter
相關代理商/技術參數
參數描述
TDF5140A 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Brushless DC motor drive circuit
TDF5140AP 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Brushless DC motor drive circuit
TDF5140AP/C1,112 功能描述:馬達/運動/點火控制器和驅動器 Brushless DC Motor Controller 18-Pin RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TDF5140AT/C1,118 功能描述:馬達/運動/點火控制器和驅動器 Brushless DC Motor Controller 18-Pin RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TDF5242 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Brushless DC motor drive circuit