參數資料
型號: THS1209CDAR
廠商: TEXAS INSTRUMENTS INC
元件分類: ADC
英文描述: 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
封裝: GREEN, PLASTIC, TSSOP-32
文件頁數: 15/33頁
文件大?。?/td> 312K
代理商: THS1209CDAR
THS1209
SLAS288B – JULY 2000 – REVISED DECEMBER 2002
www.ti.com
22
Control Register 1 (see Table 8)
BIT 11
BIT 10
BIT 9
BIT 8
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
0
1
RBACK
OFFSET
BIN/2s
R/W
RES
SRST
RESET
Table 11. Control Register 1 Bit Functions
BITS
RESET
VALUE
NAME
FUNCTION
0
RESET
Reset
Writing a 1 into this bit resets the device and sets the control register 0 and control register 1 to the reset values.
To bring the device out of reset, a 0 has to be written into this bit.
1
0
SRST
Writing a 1 into this bit resets the sync generator. When running in multichannel mode, this must be set during the
configuration cycle.
2, 3
0,0
RES
Always write 0
4
1
RES
Always write 0
5
1
RES
Always write 0
6
0
R/W
R/W, RD/WR selection
Bit 6 of control register 1 controls the function of the inputs RD and WR. When bit 6 in control register 1 is set to
1, WR becomes a R/W input and RD is disabled. From now on a read is signalled with R/W high and a write with
R/W as a low signal. If bit 6 in control register 1 is set to 0, the input RD becomes a read input and the input WR
becomes a write input.
7
0
BIN/2s
Complement select
If bit 7 of control register 1 is set to 0, the output value of the ADC is in twos complement. If bit 7 of
control register 1 is set to 1, the output value of the ADC is in binary format. Refer to Table 2 through Table 5.
8
0
OFFSET
Offset cancellation mode
Bit 8 = 0
→ normal conversion mode
Bit 8 = 1
→ offset calibration mode
If a 1 is written into bit 8 of control register 1, the device internally sets the inputs to zero and does a conver-
sion. The conversion result is stored in an offset register and subtracted from all conversions in order to
reduce the offset error.
9
0
RBACK
Debug mode
Bit 9 = 0
→ normal conversion mode
Bit 9 = 1
→ enable debug mode
When bit 9 of control register 1 is set to 1, debug mode is enabled. In this mode, the contents of control register 0
and control register 1 can be read back. The first read after bit 9 is set to 1 contains the value of control register 0.
The second read after bit 9 is set to 1 contains the value of control register 1. To bring the device back into normal
conversion mode, this bit has to be set back to 0 by writing again to control register 1.
相關PDF資料
PDF描述
THS1209IDAR 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
THS1209IDA 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
THS1209CDA 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
THS1209CDAG4 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
THS1209IDAG4 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
相關代理商/技術參數
參數描述
THS1209IDA 功能描述:模數轉換器 - ADC 12 Bit 8 MSPS Dual Ch RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
THS1209IDAG4 功能描述:模數轉換器 - ADC 12 Bit 8 MSPS Dual Ch RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
THS121 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:HIGH STABILITY MOTOR CONTROL. DIGITAL TACHOMETER. CRANK SHAFT POSITION SENSOR.
THS1215 制造商:TI 制造商全稱:Texas Instruments 功能描述:3.3-V, 12-BIT, 15 MSPS, LOW-POWER ANALOG-TO-DIGITAL CONVERTER WITH POWER DOWN
THS1215CDW 功能描述:模數轉換器 - ADC 12-Bit 15 MSPS w/Low Pwr & exc ENOB RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32