- 您現在的位置：買賣IC網 > PDF目錄98220 > THS3061DGNG4 (TEXAS INSTRUMENTS INC) 1 CHANNEL, VIDEO PREAMPLIFIER, PDSO8 PDF資料下載
參數資料
| 型號： | THS3061DGNG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1 CHANNEL, VIDEO PREAMPLIFIER, PDSO8 |
| 封裝： | GREEN, PLASTIC, MSOP-8 |
| 文件頁數： | 5/33頁 |
| 文件大?。?/td> | 1015K |
| 代理商： | THS3061DGNG4 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
www.ti.com
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
APPLICATION INFORMATION
maintain frequency response characteristics. For
most applications, a feedback-resistor value of 750
INTRODUCTION
is
recommended—a
good
compromise
between
The THS306x is a high-speed operational amplifier
bandwidth and phase margin that yields a very stable
configured in a current-feedback architecture. The
amplifier.
device is built using Texas Instruments' BiCOM-I
As shown in Table 1, to maintain the highest
process,
a
30-V,
dielectrically
isolated,
bandwidth with increasing gain, the feedback resistor
complementary bipolar process with NPN and PNP
is reduced. The advantage of dropping the feedback
transistors possessing fTs of several GHz. This
resistance (and the gain-resistor value) is that the
configuration
implements
an
exceptionally
noise of the system is also reduced compared to no
high-performance
amplifier
that
has
a
wide
reduction of these resistor values (see NOISE
bandwidth, high slew rate, fast settling time, and low
CALCULATIONS). Thus, keeping the bandwidth as
distortion.
high as possible maintains very good distortion
performance of the amplifier by keeping the excess
MAXIMUM SLEW RATE FOR REPETITIVE
loop gain as high as possible.
SIGNALS
The THS3061 and THS3062 are recommended for
Table 1. Recommended Resistor Values for
high slew rate, pulsed applications where the internal
Optimum Frequency Response
nodes of the amplifier have time to stabilize between
GAIN
RF for VCC = ±15 V
RF for VCC = ±5 V
pulses.It is recommended to have at least a 20-ns
1
750
750
delay between pulses.
2, –1
560
560
The THS3061 and THS3062 are not recommended
5
357
383
for applications with repetitive signals (sine, square,
10
200
200
sawtooth, or other types) that exceed 900 V/
μs. Using
this device in these types of applications results in an
Care must be taken to not set these values too low.
excessive current draw from the power supply and
The amplifier's output must drive the feedback
possible device damage. For applications with a high
resistance (and gain resistance), and this may place
slew rate and repetitive signals, the THS3091 and
a burden on the amplifier. The end result is that
distortion
may
actually
increase
due
to
the
(duals) are recommended instead.
low-impedance load presented to the amplifier. The
designer
must
carefully
manage
the
amplifier
RECOMMENDED FEEDBACK AND GAIN
bandwidth and the associated loading effects for
RESISTOR VALUES
optimum performance.
As with all current-feedback amplifiers, the bandwidth
The
THS3061/62
amplifiers
exhibit
very
good
of the THS306x is an inversely proportional function
distortion performance and bandwidth, and can use
of
the
value
of
the
feedback
resistor.
The
power
supplies
up
to
15
V.
The
excellent
recommended
resistors
for
optimum
frequency
current-drive capability of up to 145 mA into a 50-
response are shown in Table 1. These should be
load
allows
many
versatile
applications.
One
used as a starting point, and once optimum values
application is driving a twisted pair line (that is, a
are found, 1% tolerance resistors should be used to
telephone line). Figure 48 shows a simple circuit for
driving a twisted pair differentially.
Copyright 2002–2009, Texas Instruments Incorporated
13
相關PDF資料 |
PDF描述 |
|---|---|
| THS3061DGNRG4 | 1 CHANNEL, VIDEO PREAMPLIFIER, PDSO8 |
| THS3061DRG4 | 1 CHANNEL, VIDEO PREAMPLIFIER, PDSO8 |
| THS3062DGNRG4 | 1 CHANNEL, VIDEO PREAMPLIFIER, PDSO8 |
| THS3062DRG4 | 1 CHANNEL, VIDEO PREAMPLIFIER, PDSO8 |
| THS3062DDARG3 | 1 CHANNEL, VIDEO PREAMPLIFIER, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS3061DGNR | 功能描述:高速運算放大器 Hi-Vltg Hi-Slew-Rate Current Feedback RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS3061DGNRG4 | 功能描述:高速運算放大器 Hi-Vltg Hi-Slew-Rate Current Feedback RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS3061DR | 功能描述:高速運算放大器 Hi-Vltg Hi-Slew-Rate Current Feedback RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS3061DRG4 | 功能描述:高速運算放大器 Hi-Vltg Hi-Slew-Rate Current Feedback RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS3061EVM | 功能描述:放大器 IC 開發工具 THS3061 Eval Mod RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
發布緊急采購，3分鐘左右您將得到回復。