- 您現在的位置：買賣IC網 > PDF目錄98220 > THS3091DR (TEXAS INSTRUMENTS INC) 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 PDF資料下載
參數資料
| 型號： | THS3091DR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| 封裝： | GREEN, PLASTIC, MS-012AA, SOIC-8 |
| 文件頁數： | 16/37頁 |
| 文件大小： | 1078K |
| 代理商： | THS3091DR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
PowerPAD DESIGN CONSIDERATIONS
0.300
(7,62)
0.100
(2,54)
0.035
(0,89)
0.010
(0,254)
0.030
(0,732)
0.026
(0,66)
0.176
(4,47)
0.050
(1,27)
0.080
(2,03)
0.035
(0,89)
0.010
vias
(0.254)
0.140
(3,56)
0.060
(1,52)
0.060
(1,52)
AllUnitsininches(millimeters)
PowerPAD LAYOUT CONSIDERATIONS
DIE
Side View (a)
DIE
End View (b)
Thermal
Pad
Bottom View (c)
www.ti.com........................................................................................................................................ SLOS423G – SEPTEMBER 2003 – REVISED OCTOBER 2008
The
THS3091/5
are
available
in
a
thermally-enhanced PowerPAD family of packages.
These packages are constructed using a downset
leadframe
on
which
the
die
is
mounted
[see
Figure 71(a) and Figure 71(b)]. This arrangement
results in the lead frame being exposed as a thermal
pad
on
the
underside
of
the
package
[see
Figure 71(c)]. Because this thermal pad has direct
thermal contact with the die, excellent thermal
performance can be achieved by providing a good
thermal path away from the thermal pad. Note that
devices such as the THS3091/5 have no electrical
connection between the PowerPAD and the die.
The PowerPAD package allows for both assembly
and thermal management in one manufacturing
operation. During the surface-mount solder operation
(when the leads are being soldered), the thermal pad
can also be soldered to a copper area underneath the
Figure 72. DDA PowerPAD PCB Etch and Via
package. Through the use of thermal paths within this
Pattern
copper area, heat can be conducted away from the
package
into
either
a
ground
plane
or
other
heat-dissipating device.
1. PCB with a top-side etch pattern is shown in
The PowerPAD package represents a breakthrough
Figure 72. There should be etch for the leads as
in combining the small area and ease of assembly of
well as etch for the thermal pad.
surface
mount
with
the,
heretofore,
awkward
mechanical methods of heatsinking.
2. Place 13 holes in the area of the thermal pad.
These holes should be 0.01 inch (0,254 mm) in
diameter. Keep them small so that solder wicking
through the holes is not a problem during reflow.
3. Additional vias may be placed anywhere along
the thermal plane outside of the thermal pad
area. This helps dissipate the heat generated by
the THS3091/5 IC. These additional vias may be
larger than the 0.01-inch (0,254 mm) diameter
Figure 71. Views of Thermal Enhanced Package
vias directly under the thermal pad. They can be
larger because they are not in the thermal pad
area to be soldered so that wicking is not a
Although there are many ways to properly heatsink
problem.
the PowerPAD package, the following steps illustrate
the recommended approach.
4. Connect all holes to the internal ground plane.
Note that the PowerPAD is electrically isolated
from the silicon and all leads. Connecting the
PowerPAD to any potential voltage such as VS– is
acceptable as there is no electrical connection to
the silicon.
5. When connecting these holes to the ground
plane, do not use the typical web or spoke via
connection methodology. Web connections have
a high thermal resistance connection that is
useful for slowing the heat transfer during
soldering operations. This makes the soldering of
vias that have plane connections easier. In this
application, however, low thermal resistance is
desired for the most efficient heat transfer.
Therefore,
the
holes
under
the
THS3091/5
PowerPAD
package
should
make
their
connection to the internal ground plane with a
Copyright 2003–2008, Texas Instruments Incorporated
23
相關PDF資料 |
PDF描述 |
|---|---|
| THS3091D | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3091DRG4 | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3091DG4 | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3091DDARG3 | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3091DDAG3 | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS3091DRG4 | 功能描述:高速運算放大器 Single Lo-Distort Current Feedback RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS3091EVM | 功能描述:放大器 IC 開發工具 THS3091 Eval Module RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| THS3092 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:HIGH-VOLTAGE, LOW-DISTORTION, CURRENT-FEEDBACK OPERATIONAL AMPLIFIERS |
| THS3092D | 功能描述:高速運算放大器 Dual Hig-Vltg Low Distortion RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS3092DDA | 功能描述:高速運算放大器 Dual Hig-Vltg Low Distortion RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。