參數資料
型號： THS4502CDR
廠商： Texas Instruments, Inc.
元件分類： 運動控制電子
英文描述： WIDEBAND, LOW-DISTORTION FULLY DIFFERENTIAL AMPLIFIERS
中文描述： 寬帶，低失真全差動放大器
文件頁數： 23/40頁
文件大?。?/td> 609K
代理商： THS4502CDR
THS4502
THS4503
SLOS352D
APRIL 2002
REVISED JANUARY 2004
www.ti.com
23
INTERFACING TO AN ANALOG-TO-DIGITAL
CONVERTER
The THS4500 family of amplifiers are designed
specifically to interface to today
’
s highest-performance
analog-to-digital converters. This section highlights the
key concerns when interfacing to an ADC and provides
example ADC/fully differential amplifier interface circuits.
Key
analog-to-digital converter:
design
concerns
when
interfacing
to
an
Terminate the input source properly. In high-frequency
receiver chains, the source feeding the fully
differential amplifier requires a specific load
impedance (e.g., 50
).
Design a symmetric printed-circuit board layout.
Even-order distortion products are heavily influenced
by layout, and careful attention to a symmetric layout
will minimize these distortion products.
Minimize inductance in power supply decoupling
traces and components. Poor power supply
decoupling can have a dramatic effect on circuit
performance. Since the outputs are differential,
differential currents exist in the power supply pins.
Thus, decoupling capacitors should be placed in a
manner that minimizes the impedance of the current
loop.
Use separate analog and digital power supplies and
grounds. Noise (bounce) in the power supplies
(created by digital switching currents) can couple
directly into the signal path, and power supply noise
can create higher distortion products as well.
Use care when filtering. While an RC low-pass filter
may be desirable on the output of the amplifier to filter
broadband noise, the excess loading can negatively
impact the amplifier linearity. Filtering in the feedback
path does not have this effect.
AC-coupling allows easier circuit design. If
dc-coupling is required, be aware of the excess power
dissipation that can occur due to level-shifting the
output through the output common-mode voltage
control.
Do not terminate the output unless required. Many
open-loop,
class-A
amplifiers
termination for proper operation, but closed-loop fully
differential amplifiers drive a specific output voltage
regardless of the load impedance present.
Terminating the output of a fully differential amplifier
with a heavy load adversely effects the amplifier
’
s
linearity.
Comprehend the V
OCM
input drive requirements.
Determine if the ADC
’
s voltage reference can provide
require
50-
the required amount of current to move V
OCM
to the
desired value. A buffer may be needed.
Decouple the V
OCM
pin to eliminate the antenna
effect. V
OCM
is a high-impedance node that can act as
an antenna. A large decoupling capacitor on this node
eliminates this problem.
Be cognizant of the input common-mode range. If the
input signal is referenced around the negative power
supply rail (e.g., around ground on a single 5 V
supply), then the THS4500/1 accommodates the
input signal. If the input signal is referenced around
midrail, choose the THS4502/3 for the best operation.
Packaging makes a difference at higher frequencies.
If possible, choose the smaller, thermally enhanced
MSOP package for the best performance. As a rule,
lower
junction
temperatures
performance. If possible, use a thermally enhanced
package, even if the power dissipation is relatively
small compared to the maximum power dissipation
rating to achieve the best results.
Comprehend the effect of the load impedance seen by
the fully differential amplifier when performing
system-level intercept point calculations. Lighter
loads (such as those presented by an ADC) allow
smaller intercept points to support the same level of
intermodulation distortion performance.
provide
better
EXAMPLE ANALOG-TO-DIGITAL
CONVERTER DRIVER CIRCUITS
The THS4500 family of devices is designed to drive
high-performance ADCs with extremely high linearity,
allowing for the maximum effective number of bits at the
output of the data converter. Two representative circuits
shown below highlight single-supply operation and split
supply operation. Specific feedback resistor, gain resistor,
and feedback capacitor values are not specified, as their
values depend on the frequency of interest. Information on
calculating these values can be found in the applications
material above.
Figure 97
+
V
OCM
+
12 Bit/80 MSps
CM
IN
IN
5 V
5 V
5 V
V
S
10
μ
F
0.1
μ
F
10
μ
F
0.1
μ
F
THS4503
R
f
R
f
C
F
C
F
1
μ
F
R
g
R
g
0.1
μ
F
R
T
R
S
ADS5410
Using the THS4503 With the ADS5410
R
iso
R
iso
相關PDF資料
PDF描述
THS4502CDRG4 WIDEBAND, LOW-DISTORTION FULLY DIFFERENTIAL AMPLIFIERS
THS4502CDT WIDEBAND, LOW-DISTORTION FULLY DIFFERENTIAL AMPLIFIERS
THS4502IDDT WIDEBAND, LOW-DISTORTION FULLY DIFFERENTIAL AMPLIFIERS
THS4502IDGKR WIDEBAND, LOW-DISTORTION FULLY DIFFERENTIAL AMPLIFIERS
THS4502IDGKRG4 WIDEBAND, LOW-DISTORTION FULLY DIFFERENTIAL AMPLIFIERS
相關代理商/技術參數
參數描述
THS4502CDRB 制造商:TI 制造商全稱:Texas Instruments 功能描述:WIDEBAND, LOW-DISTORTION FULLY DIFFERENTIAL AMPLIFIERS
THS4502CDRG4 功能描述:特殊用途放大器 Hi-Sp Fully-Diff Amp RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel
THS4502CDT 制造商:TI 制造商全稱:Texas Instruments 功能描述:WIDEBAND, LOW-DISTORTION FULLY DIFFERENTIAL AMPLIFIERS
THS4502EVM 功能描述:放大器 IC 開發工具 THS4502 Eval Mod RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V
THS4502ID 功能描述:特殊用途放大器 Hi-Sp Fully-Diff Amp RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*