參數資料
型號： TLC2543QDWRQ1
廠商： TEXAS INSTRUMENTS INC
元件分類： ADC
英文描述： 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20
封裝： PLASTIC, SOIC-20
文件頁數： 9/25頁
文件大小： 413K
代理商： TLC2543QDWRQ1
TLC2543Q1
12BIT ANALOGTODIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SGLS218D NOVEMBER 2003 REVISED MAY 2008
17
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
data format and pad bits (continued)
When CS is held low continuously, the first data bit of the newly completed conversion occurs on DATA OUT
on the rising edge of EOC. When a new conversion is started after the last falling edge of I/O CLOCK, EOC goes
low and the serial output is forced to a setting of 0 until EOC goes high again.
When CS is negated between conversions, the first data bit occurs on DATA OUT on the falling edge of CS.
On each subsequent falling edge of I/O CLOCK after the first data bit appears, the data is changed to the next
bit in the serial conversion result until the required number of bits has been output.
chip-select input (CS)
CS enables and disables the device. During normal operation, CS should be low. Although the use of CS is not
necessary to synchronize a data transfer, it can be brought high between conversions to coordinate the data
transfer of several devices sharing the same bus.
When CS is brought high, the serial-data output is immediately brought to the high-impedance state, releasing
its output data line to other devices that may share it. After an internally generated debounce time, I/O CLOCK
is inhibited, thus preventing any further change in the internal state.
When CS is subsequently brought low again, the device is reset. CS must be held low for an internal debounce
time before the reset operation takes effect. After CS is debounced low, I/O CLOCK must remain inactive (low)
for a minimum time before a new I/O cycle can start.
CS can interrupt any ongoing data transfer or any ongoing conversion. When CS is debounced low long enough
before the end of the current conversion cycle, the previous conversion result is saved in the internal output
buffer and shifted out during the next I/O cycle.
power-down features
When a binary address of 1110 is clocked into the input data register during the first four I/O CLOCK cycles,
the power-down mode is selected. Power down is activated on the falling edge of the fourth I/O CLOCK pulse.
During power down, all internal circuitry is put in a low-current standby mode. No conversions are performed,
and the internal output buffer keeps the previous conversion cycle data results provided that all digital inputs
are held above VCC 0.5 V or below 0.5 V. The I/O logic remains active so the current I/O cycle must be
completed even when the power-down mode is selected. Upon power-on reset and before the first I/O cycle,
the converter normally begins in the power-down mode. The device remains in the power-down mode until a
valid input address (other than 1110) is clocked in. Upon completion of that I/O cycle, a normal conversion is
performed with the results being shifted out during the next I/O cycle.
相關PDF資料
PDF描述
TLC2543MDBREP 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20
TLC2543QDWREP 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20
TLC2543MFK 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, CQCC20
TLC2552IDGK 2-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8
TLC2552IDR 2-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8
相關代理商/技術參數
參數描述
TLC254ACD 功能描述:運算放大器 - 運放 Quad LinCMOS RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
TLC254ACDG4 功能描述:運算放大器 - 運放 LinCMOS Quad OP AMP RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
TLC254ACN 功能描述:運算放大器 - 運放 Lin CMOS Quad RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
TLC254ACNE4 功能描述:運算放大器 - 運放 LinCMOS Quad Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
TLC254BCD 功能描述:運算放大器 - 運放 LinCMOS Quad RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*