- 您現在的位置：買賣IC網 > PDF目錄98242 > TLC5540CNSLE (TEXAS INSTRUMENTS INC) 1-CH 8-BIT FLASH METHOD ADC, PARALLEL ACCESS, PDSO24 PDF資料下載
參數資料
| 型號： | TLC5540CNSLE |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 1-CH 8-BIT FLASH METHOD ADC, PARALLEL ACCESS, PDSO24 |
| 封裝： | PLASTIC, SOP-24 |
| 文件頁數： | 2/21頁 |
| 文件大?。?/td> | 407K |
| 代理商： | TLC5540CNSLE |
TLC5540
SLAS105D JANUARY 1995 REVISED APRIL 2004
www.ti.com
10
APPLICATION INFORMATION
grounding and power supply considerations
A signal ground is a low-impedance path for current to return to the source. Inside the TLC5540 A/D converter,
the analog ground and digital ground are connected to each other through the substrate, which has a very small
resistance (~30
) to prevent internal latch-up. For this reason, it is strongly recommended that a printed circuit
board (PCB) of at least 4 layers be used with the TLC5540 and the converter DGND and AGND pins be
connected directly to the analog ground plane to avoid a ground loop. Figure 11 shows the recommended
decoupling and grounding scheme for laying out a multilayer PC board with the TLC5540. This scheme ensures
that the impedance connection between AGND and DGND is minimized so that their potential difference is
negligible and noise source caused by digital switching current is eliminated.
0.1
F
0.1
F
11
13
24
2
14
15
18
20
21
VDDD
GND
VDDA
AGND
TLC5540
Signal Plane
Analog Ground Plane
Analog Supply Plane
Signal Plane
Digital Supply Plane
0.1
F
0.1
F
0.1
F
Figure 11. AVDD, DVDD, AGND, and DGND Connections
printed circuit board (PCB) layout considerations
When designing a circuit that includes high-speed digital and precision analog signals such as a high speed
ADC, PCB layout is a key component to achieving the desired performance. The following recommendations
should be considered during the prototyping and PCB design phase:
D Separate analog and digital circuitry physically to help eliminate capacitive coupling and crosstalk. When
separate analog and digital ground planes are used, the digital ground and power planes should be several
layers from the analog signals and power plane to avoid capacitive coupling.
D Full ground planes should be used. Do not use individual etches to return analog and digital currents or
partial ground planes. For prototyping, breadboards should be constructed with copper clad boards to
maximize ground plane.
D The conversion clock, CLK, should be terminated properly to reduce overshoot and ringing. Any jitter on
the conversion clock degrades ADC performance. A high-speed CMOS buffer such as a 74ACT04 or
74AC04 positioned close to the CLK terminal can improve performance.
D Minimize all etch runs as much as possible by placing components very close together. It also proves
beneficial to place the ADC in a corner of the PCB nearest to the I/O connector analog terminals.
D It is recommended to place the digital output data latch (if used) as close to the TLC5540 as possible to
minimize capacitive loading. If D0 through D7 must drive large capacitive loads, internal ADC noise may
be experienced.
相關PDF資料 |
PDF描述 |
|---|---|
| TLC5540INS | 1-CH 8-BIT FLASH METHOD ADC, PARALLEL ACCESS, PDSO24 |
| TLC556lDR | DUAL PULSE; RECTANGULAR, 1.2 MHz, TIMER, PDSO14 |
| TLC556lD | DUAL PULSE; RECTANGULAR, 1.2 MHz, TIMER, PDSO14 |
| TLC556MFK | DUAL PULSE; RECTANGULAR, 1.2 MHz, TIMER, CQCC20 |
| TLC5602CDW | PARALLEL, 8 BITS INPUT LOADING, 0.03 us SETTLING TIME, 8-BIT DAC, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLC5540CNSR | 功能描述:模數轉換器 - ADC 8bit 40Msps 1ch 5V RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLC5540CNSRG4 | 功能描述:模數轉換器 - ADC 8-Bit 40 MSPS 1-Ch Internal S&H Lo Pwr RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLC5540CPW | 功能描述:模數轉換器 - ADC 8-Bit 40 MSPS 1-Ch Internal S&H Lo Pwr RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLC5540CPWG4 | 功能描述:模數轉換器 - ADC 8-Bit 40 MSPS 1-Ch Internal S&H Lo Pwr RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLC5540CPWR | 功能描述:模數轉換器 - ADC 8-Bit 40 MSPS 1-Ch Internal S&H Lo Pwr RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。