- 您現在的位置：買賣IC網 > PDF目錄98257 > TLV5610IYZT (TEXAS INSTRUMENTS INC) SERIAL INPUT LOADING, 3 us SETTLING TIME, 12-BIT DAC, BGA20 PDF資料下載
參數資料
| 型號： | TLV5610IYZT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | DAC |
| 英文描述： | SERIAL INPUT LOADING, 3 us SETTLING TIME, 12-BIT DAC, BGA20 |
| 封裝： | GREEN, WCSP-20 |
| 文件頁數： | 3/14頁 |
| 文件大?。?/td> | 180K |
| 代理商： | TLV5610IYZT |
www.ti.com
USING THE TLV5610IYZ WAFER CHIP-SCALE PACKAGE (WCSP)
BottomView
TopView
SBAS389A – JULY 2006 – REVISED JULY 2006
TLV5610 qualifications are done using a wire-bonded small outline (SO) package. The qualifications include:
steady state life, thermal shock, ESD, latch-up, biased HAST, autoclave, and characterization. These qualified
devices are orderable as TLV5610IDW.
NOTE: The wafer chip-scale package (WCSP) for the TLV5610IYZ uses the same die as TLV5610IDW, but is
not qualified. WCSP qualification, including board level reliability (BLR), is the responsibility of the customer.
It is recommended that underfill be used for increased reliability. BLR is application-dependent, but may include
tests such as: temperature cycling, drop test, key push, bend, vibration, and package shear.
For general guidelines on board assembly of the WCSP, the following documentation provides more details:
Application Report NanoStar & NanoFree 300
NOTE: The use of underfill is required and greatly reduces the risk of thermal mismatch fails.
Underfill is an epoxy/adhesive that may be added during the board assembly process to improve board
level/system level reliability. The process is to dispense the epoxy under the dice after die attach reflow. The
epoxy adheres to the body of the device and to the printed-circuit board. It reduces stress placed upon the
solder joints because of thermal coefficient of expansion (TCE) mismatch between the board and the
component. Underfill material is highly filled with silica or other fillers to increase epoxy modulus, reduce creep
sensitivity, and decrease material TCE.
NOTE: The recommendation for peak flow temperatures of +250
°C to +260°C is based on general empirical
results that indicate that this temperature range is needed to facilitate good wetting of the solder bump to the
substrate or circuit board pad. Lower peak temperatures may cause nonwets (cold solder joints).
A.
All linear dimensions are in millimeters.
B.
This drawing is subject to change without notice.
Figure 10. TLV5610IYZ Wafer Chip-Scale Package
11
相關PDF資料 |
PDF描述 |
|---|---|
| TLV5610IYZR | SERIAL INPUT LOADING, 3 us SETTLING TIME, 12-BIT DAC, BGA20 |
| TLV5610IYZ | SERIAL INPUT LOADING, 3 us SETTLING TIME, 12-BIT DAC, BGA20 |
| TLV5613CDWRG4 | PARALLEL, WORD INPUT LOADING, 1 us SETTLING TIME, 12-BIT DAC, PDSO20 |
| TLV5613IDW | PARALLEL, WORD INPUT LOADING, 1 us SETTLING TIME, 12-BIT DAC, PDSO20 |
| TLV5613IDWR | PARALLEL, WORD INPUT LOADING, 1 us SETTLING TIME, 12-BIT DAC, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLV5613 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.7 V TO 5.5 V 12-BIT PARALLEL DIGITAL-TO-ANALOG CONVERTER WITH POWER DOWN |
| TLV5613CDW | 功能描述:數模轉換器- DAC 12bit CMOS DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| TLV5613CDWG4 | 功能描述:數模轉換器- DAC 12bit CMOS DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| TLV5613CDWR | 功能描述:數模轉換器- DAC 12-Bit DAC Parallel Voltage Out RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| TLV5613CDWRG4 | 功能描述:數模轉換器- DAC 12-Bit DAC Parallel Voltage Out RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。