參數資料
型號: TMP320F2810GHHS
廠商: Texas Instruments, Inc.
元件分類: 數字信號處理
英文描述: DIGITAL SIGNAL PROCESSORS
中文描述: 數字信號處理器
文件頁數: 69/103頁
文件大?。?/td> 1341K
代理商: TMP320F2810GHHS
TMS320F2810, TMS320F2812
DIGITAL SIGNAL PROCESSORS
SPRS174B
APRIL 2001
REVISED SEPTEMBER 2001
69
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251
1443
enhanced analog-to-digital converter (ADC) module (continued)
To obtain the specified accuracy of the ADC, proper board layout is very critical. To the best extent possible,
traces leading to the ADCIN pins should not run in close proximity to the digital signal paths. This is to minimize
switching noise on the digital lines from getting coupled to the ADC inputs. Furthermore, proper isolation
techniques must be used to isolate the ADC module power pins (such as V
CCA
, V
REFHI
, and V
SSA
) from the
digital supply.
Notes:
1.
The ADC registers are accessed at the SYSCLKOUT rate. The internal timing of the ADC module is
controlled by the high-speed peripheral clock (HSPCLK).
2.
The behavior of the ADC module based on the state of the ADCENCLK and HALT signals is as follows:
ADCENCLK:
On reset, this signal will be low. While reset is active-low (XRS) the clock to the register will still
function. This is necessary to make sure all registers and modes go into their default reset state. The analog
module will however be in a low-power inactive state. As soon as reset goes high, then the clock to the
registers will be disabled. When the user sets the ADCENCLK signal high, then the clocks to the registers
will be enabled and the analog module will be enabled. There will be a certain time delay (ms range) before
the ADC is stable and can be used.
HALT:
This signal only affects the analog module. It does not affect the registers. If low, the ADC module is
powered. If high, the ADC module goes into low-power mode. The HALT mode will stop the clock to the CPU,
which will stop the HSPCLK. Therefore the ADC register logic will be turned off indirectly.
P
相關PDF資料
PDF描述
TMX320F2810PGFA DIGITAL SIGNAL PROCESSORS
TMP320F2810PGFA DIGITAL SIGNAL PROCESSORS
TMX320F2810PGFAEP Digital Signal Processors
TMP320F2810PGFAEP Digital Signal Processors
TMX320F2810PGFS DIGITAL SIGNAL PROCESSORS
相關代理商/技術參數
參數描述
TMP320F2810PBKA 制造商:Texas Instruments 功能描述:
TMP320F2810PBKAEP 制造商:TI 制造商全稱:Texas Instruments 功能描述:Digital Signal Processors
TMP320F2810PBKS 功能描述:IC DSP W/FLASH128=LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:TMS320F281x, C2000™ 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C,SPI,UART/USART,USB 外圍設備:欠壓檢測/復位,POR,PWM,WDT 輸入/輸出數:14 程序存儲器容量:8KB(4K x 16) 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP(0.300",7.62mm) 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
TMP320F2810PGFA 制造商:TI 制造商全稱:Texas Instruments 功能描述:DIGITAL SIGNAL PROCESSORS
TMP320F2810PGFAEP 制造商:TI 制造商全稱:Texas Instruments 功能描述:Digital Signal Processors