參數資料
型號: TMS320C6711PGE150
廠商: Texas Instruments, Inc.
元件分類: 數字信號處理
英文描述: FIXED-POINT DIGITAL SIGNAL PROCESSORS
中文描述: 定點數字信號處理器
文件頁數: 31/123頁
文件大小: 1205K
代理商: TMS320C6711PGE150
www.ti.com
3.2.10
Peripheral Interrupt Expansion (PIE) Block
3.2.11
External Interrupts (XINT1, XINT2, XNMI)
3.2.12
Oscillator and PLL
3.2.13
Watchdog
3.2.14
Peripheral Clocking
3.2.15
Low-Power Modes
TMS320F2808, TMS320F2806
TMS320F2801, UCD9501
Digital Signal Processors
SPRS230F–OCTOBER 2003–REVISED SEPTEMBER 2005
The PIE block serves to multiplex numerous interrupt sources into a smaller set of interrupt inputs. The
PIE block can support up to 96 peripheral interrupts. On the 280x, 43 of the possible 96 interrupts are
used by peripherals. The 96 interrupts are grouped into blocks of 8 and each group is fed into 1 of 12
CPU interrupt lines (INT1 to INT12). Each of the 96 interrupts is supported by its own vector stored in a
dedicated RAM block that can be overwritten by the user. The vector is automatically fetched by the CPU
on servicing the interrupt. It takes 8 CPU clock cycles to fetch the vector and save critical CPU registers.
Hence the CPU can quickly respond to interrupt events. Prioritization of interrupts is controlled in
hardware and software. Each individual interrupt can be enabled/disabled within the PIE block.
The 280x supports three masked external interrupts (XINT1, XINT2, XNMI). XNMI can be connected to
the INT13 or NMI interrupt of the CPU. Each of the interrupts can be selected for negative, positive, or
both negative and positive edge triggering and can also be enabled/disabled (including the XNMI). The
masked interrupts also contain a 16-bit free running up counter, which is reset to zero when a valid
interrupt edge is detected. This counter can be used to accurately time stamp the interrupt. Unlike the
281x devices, there are no dedicated pins for the external interrupts. Rather, any Port A GPIO pin can be
configured to trigger any external interrupt.
The 280x can be clocked by an external oscillator or by a crystal attached to the on-chip oscillator circuit.
A PLL is provided supporting up to 10 input-clock-scaling ratios. The PLL ratios can be changed on-the-fly
in software, enabling the user to scale back on operating frequency if lower power operation is desired.
Refer to the Electrical Specification section for timing details. The PLL block can be set in bypass mode.
The 280x devices contain a watchdog timer. The user software must regularly reset the watchdog counter
within a certain time frame; otherwise, the watchdog will generate a reset to the processor. The watchdog
can be disabled if necessary.
The clocks to each individual peripheral can be enabled/disabled so as to reduce power consumption
when a peripheral is not in use. Additionally, the system clock to the serial ports (except eCAN) and the
ADC blocks can be scaled relative to the CPU clock. This enables the timing of peripherals to be
decoupled from increasing CPU clock speeds.
The 280x devices are full static CMOS devices. Three low-power modes are provided:
IDLE:
Place CPU into low-power mode. Peripheral clocks may be turned off selectively and only
those peripherals that need to function during IDLE are left operating. An enabled interrupt
from an active peripheral or the watchdog timer will wake the processor from IDLE mode.
Turn off clock to CPU and peripherals. This mode leaves the oscillator and PLL functional.
An external interrupt event will wake the processor and the peripherals. Execution begins
on the next valid cycle after detection of the interrupt event
Turn off oscillator. This mode basically shuts down the device and places it in the lowest
possible power consumption mode. A reset or external signal can wake the device from
this mode.
STANDBY:
HALT:
Functional Overview
31
相關PDF資料
PDF描述
TMS320C6711PGE120 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6711NA167 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6711NA150 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6711NA120 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6711NA100 FIXED-POINT DIGITAL SIGNAL PROCESSORS
相關代理商/技術參數
參數描述
TMS320C6712CGDP150 制造商:Texas Instruments 功能描述:
TMS320C6712DGDP150 功能描述:數字信號處理器和控制器 - DSP, DSC Floating-Pt Dig Sig Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320C6712DZDP150 功能描述:數字信號處理器和控制器 - DSP, DSC Floating-Pt Dig Sig Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320C6712GFN100 功能描述:IC FLOATING POINT DSP 256-BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP(數字式信號處理器) 系列:TMS320C67x 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI,以太網,RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA,F(xiàn)CBGA 供應商設備封裝:431-FCPBGA(20x20) 包裝:托盤
TMS320C6713BGDP225 功能描述:數字信號處理器和控制器 - DSP, DSC Floating-Pt Dig Sig Processors RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT