參數資料
型號： TMS320F28044PZQ
廠商： Texas Instruments, Inc.
元件分類： 數字信號處理
英文描述： Digital Signal Processor
中文描述： 數字信號處理器
文件頁數： 37/105頁
文件大小： 768K
代理商： TMS320F28044PZQ
www.ti.com
A
3.6.2
Watchdog Block
TMS320F28044
Digital Signal Processor
SPRS357A–AUGUST 2006–REVISED OCTOBER 2006
Table 3-13. Possible PLL Configuration Modes
SYSCLKOUT
(CLKIN)
OSCCLK/2
PLL MODE
REMARKS
PLLSTS[CLKINDIV]
Invoked by the user setting the PLLOFF bit in the PLLSTS register. The PLL block
is disabled in this mode. This can be useful to reduce system noise and for low
power operation. The PLLCR register must first be set to 0x0000 (PLL Bypass)
before entering this mode. The CPU clock (CLKIN) is derived directly from the
input clock on either X1/X2, X1 or XCLKIN.
PLL Bypass is the default PLL configuration upon power-up or after an external
reset (XRS). This mode is selected when the PLLCR register is set to 0x0000 or
while the PLL locks to a new frequency after the PLLCR register has been
modified. In this mode, the PLL itself is bypassed but the PLL is not turned off.
Achieved by writing a non-zero value n into the PLLCR register. Upon writing to the
PLLCR the device will switch to PLL Bypass mode until the PLL locks.
0
PLL Off
1
OSCCLK
0
OSCCLK/2
PLL Bypass
1
OSCCLK
PLL Enable
0
OSCCLK*n/2
3.6.1.3
Loss of Input Clock
In PLL-enabled and PLL-bypass mode, if the input clock OSCCLK is removed or absent, the PLL will still
issue a "limp-mode" clock. The limp-mode clock continues to clock the CPU and peripherals at a typical
frequency of 1-5 MHz. Limp mode is not specified to work from power-up, only after input clocks have
been present initially. In PLL bypass mode, the limp mode clock from the PLL is automatically routed to
the CPU if the input clock is removed or absent.
Normally, when the input clocks are present, the watchdog counter decrements to initiate a watchdog
reset or WDINT interrupt. However, when the external input clock fails, the watchdog counter stops
decrementing (i.e., the watchdog counter does not change with the limp-mode clock). In addition to this,
the device will be reset and the “Missing Clock Status” (MCLKSTS) bit will be set. These conditions could
be used by the application firmware to detect the input clock failure and initiate necessary shut-down
procedure for the system.
NOTE
Applications in which the correct CPU operating frequency is absolutely critical should
implement a mechanism by which the DSP will be held in reset, should the input clocks
ever fail. For example, an R-C circuit may be used to trigger the XRS pin of the DSP,
should the capacitor ever get fully charged. An I/O pin may be used to discharge the
capacitor on a periodic basis to prevent it from getting fully charged. Such a circuit would
also help in detecting failure of the flash memory and the V
DD3VFL
rail.
The watchdog block on the 28044 is similar to the one used on the 240x and 281x devices. The watchdog
module generates an output pulse, 512 oscillator clocks wide (OSCCLK), whenever the 8-bit watchdog up
counter has reached its maximum value. To prevent this, the user disables the counter or the software
must periodically write a 0x55 + 0xAA sequence into the watchdog key register which will reset the
watchdog counter.
Figure 3-10
shows the various functional blocks within the watchdog module.
Submit Documentation Feedback
Functional Overview
37
相關PDF資料
PDF描述
TMS320LC545 Digital Signal Processors(20/25ns指令周期， 高性能，大并行度，特殊指令集可有效實現多種復雜算法及應用的DSP)
TMS320LC546 Digital Signal Processors(20/25ns指令周期， 高性能，大并行度，特殊指令集可有效實現多種復雜算法及應用的DSP)
TMS320LC57S Digital Signal Processors(35/50ns指令周期，并行邏輯單元，可編程PLL，全雙工同步串行口的DSP)
TMS320UVC5409 Fixed-Point Digital Signal Processor(定點DSP)
TMS320VC203 Digital Signal Processors(50ns指令周期， 空閑狀態CPU全關斷，先進的外圍，多種PLL可選)
相關代理商/技術參數
參數描述
TMS320F28044PZS 功能描述:數字信號處理器和控制器 - DSP, DSC 32-Bit DSC w/ 128KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320F28045PZA 制造商:Texas Instruments 功能描述:- Trays
TMS320F28045PZS 制造商:Texas Instruments 功能描述:- Trays
TMS320F28050PNQ 制造商:Texas Instruments 功能描述:GIZMO
TMS320F28050PNS 制造商:Texas Instruments 功能描述:GIZMO
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*