- 您現在的位置：買賣IC網 > PDF目錄382662 > TOP242R-TL SMPS Controller PDF資料下載
參數資料
| 型號： | TOP242R-TL |
| 英文描述： | SMPS Controller |
| 中文描述： | 開關電源控制器 |
| 文件頁數： | 6/52頁 |
| 文件大小： | 457K |
| 代理商： | TOP242R-TL |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
TOP242-250
6
H
9/02
of typically 4.8 V to 5.8 V by turning the high-voltage current
source on and off as shown in Figure 8. The auto-restart
circuit has a divide-by-eight counter which prevents the out-
put MOSFET from turning on again until eight discharge/charge
cycles have elapsed. This is accomplished by enabling the
output MOSFET only when the divide-by-eight counter reaches
full count (S7). The counter effectively limits
TOPSwitch-GX
power dissipation by reducing the auto-restart duty cycle to
typically 4%. Auto-restart mode continues until output
voltage regulation is again achieved through closure of the
feedback loop.
Design Ideas 4
Quality and Reliability 6
Package Information 7
~
DPA-SwitchDC-DC Seminar 8
LinkSwitch & TinySwitch-IIAC-DC Seminar 9
TOPSwitch-GXAC-DC Seminar 10
Sales Representatives and Distributors 11
~
~
PI-2545-082299
S1
S2
~
S6
S7
S1
S2
~
S6
S7
S0
S1
S7
S0
S0
5.8 V
S7
0 V
0 V
0 V
V
LINE
V
C
V
DRAIN
V
OUT
0 V
Note: S0 through S7 are the output states of the auto-restart counter
2
1
2
3
4
~
~
~
S6
S7
~
~
~
V
UV
~
~
S2
CONTROL (C) Pin Operation
The CONTROL pin is a low impedance node that is capable of
receiving a combined supply and feedback current. During
normal operation, a shunt regulator is used to separate the feed-
back signal from the supply current. CONTROL pin voltage
V
is the supply voltage for the control circuitry including the
MOSFET gate driver. An external bypass capacitor closely
connected between the CONTROL and SOURCE pins is
required to supply the instantaneous gate drive current. The
total amount of capacitance connected to this pin also sets the
auto-restart timing as well as control loop compensation.
When rectified DC high voltage is applied to the DRAIN pin
during start-up, the MOSFET is initially off, and the
CONTROL pin capacitor is charged through a switched high
voltage current source connected internally between the DRAIN
and CONTROL pins. When the CONTROL pin voltage V
C
reaches approximately 5.8 V, the control circuitry is activated
and the soft-start begins. The soft-start circuit gradually
increases the duty cycle of the MOSFET from zero to the maxi-
mum value over approximately 10 ms. If no external feedback/
supply current is fed into the CONTROL pin by the end of the
soft-start, the high voltage current source is turned off and the
CONTROL pin will start discharging in response to the supply
current drawn by the control circuitry. If the power supply is
designed properly, and no fault condition such as open loop or
shorted output exists, the feedback loop will close, providing
external CONTROL pin current, before the CONTROL pin
voltage has had a chance to discharge to the lower threshold
voltage of approximately 4.8 V (internal supply under-voltage
lockout threshold). When the externally fed current charges
the CONTROL pin to the shunt regulator voltage of 5.8 V, cur-
rent in excess of the consumption of the chip is shunted to
SOURCE through resistor R
as shown in Figure 2. This
current flowing through R
controls the duty cycle of the power
MOSFET to provide closed loop regulation. The shunt
regulator has a finite low output impedance Z
that sets the
gain of the error amplifier when used in a primary feedback
configuration. The dynamic impedance Z
of the CONTROL
pin together with the external CONTROL pin capacitance sets
the dominant pole for the control loop.
When a fault condition such as an open loop or shorted output
prevents the flow of an external current into the CONTROL
pin, the capacitor on the CONTROL pin discharges towards
4.8 V. At 4.8 V, auto-restart is activated which turns the output
MOSFET off and puts the control circuitry in a low current
standby mode. The high-voltage current source turns on and
charges the external capacitance again. A hysteretic internal
supply under-voltage comparator keeps V
within a window
Oscillator and Switching Frequency
The internal oscillator linearly charges and discharges an
internal capacitance between two voltage levels to create a
sawtooth waveform for the pulse width modulator. This
Figure 8. Typical Waveforms for (1) Power Up (2) Normal Operation (3) Auto-restart (4) Power Down.
相關PDF資料 |
PDF描述 |
|---|---|
| TOP243F | SMPS Controller |
| TOP243G | SMPS Controller |
| TOP243G-TL | SMPS Controller |
| TOP250F | SMPS Controller |
| TOP250R-TL | SMPS Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TOP242Y | 功能描述:IC OFFLINE SWIT UVLO HV TO220 RoHS:否 類別:集成電路 (IC) >> PMIC - AC-DC 轉換器，離線開關 系列:TOPSwitch®-GX 標準包裝:1 系列:FPS™ 輸出隔離:隔離 頻率范圍:61kHz ~ 73kHz 輸入電壓:8 V ~ 26 V 輸出電壓:650V 功率（瓦特）:12W 工作溫度:-40°C ~ 115°C 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-MDIP 包裝:Digi-Reel® 其它名稱:FSL206MRBNFSDKR |
| TOP242Y- | 制造商:POWERINT 制造商全稱:Power Integrations, Inc. 功能描述:TOPSwitch-GX Family Extended Power, Design Flexible, EcoSmart, Integrated Off-line Switcher |
| TOP242Y/F | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Up to 290 W Extended power. design flexible. |
| TOP242YN | 功能描述:交流/直流開關轉換器 14W 85-265 VAC 22 W230 VAC RoHS:否 制造商:STMicroelectronics 輸出電壓:800 V 輸入/電源電壓（最大值）:23.5 V 輸入/電源電壓（最小值）:11.5 V 開關頻率:115 kHz 電源電流:1.6 mA 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SSO-10 封裝:Reel |
| TOP242YN- | 制造商:POWERINT 制造商全稱:Power Integrations, Inc. 功能描述:TOPSwitch-GX Family Extended Power, Design Flexible, EcoSmart, Integrated Off-line Switcher |
發布緊急采購，3分鐘左右您將得到回復。