- 您現在的位置：買賣IC網 > PDF目錄385942 > TORX196 (Toshiba Corporation) FIBER OPTIC RECEIVING MODULE PDF資料下載
參數資料
| 型號： | TORX196 |
| 廠商： | Toshiba Corporation |
| 英文描述： | FIBER OPTIC RECEIVING MODULE |
| 中文描述： | 光纖接收模塊 |
| 文件頁數： | 7/9頁 |
| 文件大小： | 161K |
| 代理商： | TORX196 |
TORX196
2001-08-10
7
7. Precaution on Use
(1)
Maximum rating
The maximum ratings are the limit values which must not be exceeded during operation of device.
None of these rating value must not be exceeded. If the maximum rating value is exceeded, the
characteristics of devices may never be restored properly. In extreme cases, the device may be
permanently damages.
Soldering
Optical modules are comprised of internal semiconductor devices. However, in principle, optical
modules are optical components. During soldering, ensure that flux does not contact with the emitting
surface or the detecting surface. Also ensure that proper flux removal is conducted after soldering.
Some optical modules come with a protective cap. The protective cap is used to avoid malfunction
when the optical module is not in use. Note that it is not dust or waterproof.
As mentioned before, optical modules are optical components. Thus, in principle, soldering where
there may be flux residue and flux removal after soldering is not recommended. Toshiba recommend
that soldering be performed without the optical module mounted on the board. Then, after the board
has been cleaned, the optical module should be soldered on to the board manually.
If the optical module cannot be soldered manually, use non
halogen (chlorine
free) flux and make
sure, without cleaning, there is no residue such as chlorine. This is one of the ways to eliminate the
effects of flux. In such a cases, be sure to check the devices’ reliability.
Noise resistance
It is believed that the use of optical transfer devices improve noise resistance. In theory, optical fiber
is not affected by noise at all. However, receiving modules which handle signals whose level is
extremely small, are susceptible to noise.
TOSLINK improve noise resistance to use a conductive case. However, the current signal output by
the optical receiving modules' photodiode is extremely small. Thus, in some environments, shielding
the case may not achieve sufficient noise resistance.
First systems which incorporate TOSLINK, Toshiba recommend testing using the actual device to
check its noise resistance.
Use a simple noise filter on TOSLINK fiber optic transceiving module's power line. If the ripple in the
power supply used is significant, reinforce the filter.
The optical module is to be used in an area which is susceptible to radiated noise, increase the
shielding by covering the optical module and the power line filter with a metallic cover.
Vibration and shock
This module is plastic sealed and has its wire fixed by resin. This structure is relatively resistant to
vibration and shock. In actual equipment, there are sometime cases in which vibration, shock, or
stress is applied to soldered parts or connected parts, resulting in lines cut. A care must be taken in
the design of equipment which will be subject to high levels of vibration.
Attaching the fiber optic receiving module
Solder the fixed pins (pins 4 and 5) of the fiber optic receiving module TORX196 to the printed circuit
board in order to fix it to the board.
Shielding and wiring pattern of fiber optic receiving modules
To shield, connect the fixed pins (pins 5 and 6) of fiber optic transceiving module TORX196 to the
GND.
Where the fiber optic receiving module uses conductive resin, be careful that the case does not touch
wiring (including land).
To improve noise resistance, shield the optical module and the power line filter using a metallic cover.
Solvent
When using solvent for flux removal, do not use a high acid or high alkali solvent. Be careful not to
pour solvent in to the optical connector ports. If solvent is inadvertently poured in to them, clean it off
using cotton tips.
Protective cap
When the TORX196 is not in use, attach the protective cap.
Supply voltage
Use the supply voltage within the recommended operating condition (V
CC
= 5 ± 0.25 V). Make sure
that supply voltage does not exceed the maximum rating value of 7 V, even for an instant.
(10) Output
If the receiver output is at low and is connected to the power supply, or if the output is high and is
connected to GND, the internal IC may be destroyed.
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
相關PDF資料 |
PDF描述 |
|---|---|
| TOTX193K | Fiber Optic Transmitting Module for Digital Audio Equipment and Navigation System(用于數字音頻設備的光纖傳送模塊) |
| TOTX196 | Fiber Optic Transmitting Module for Simplex Digital Signal Transmission(光纖傳送模塊（用于單向數字信號傳輸 ）) |
| TP0604 | P-Channel Enhancement-Mode Vertical DMOS FET Quad Array(擊穿電壓-40V，低門限2.4V，P溝道增強型垂直DMOS結構場效應管四陣列) |
| TP0604 | CONNECTOR ACCESSORY |
| TP0604N3 | CONNECTOR ACCESSORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TORX196(F) | 功能描述:光纖發射器、接收器、收發器 TOSLINK RECEIVR DATA RATE UP TO 10Mb/s RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
| TORX198 | 制造商:Toshiba America Electronic Components 功能描述:RX Optical Fiber 6Mbps 6-Pin |
| TORX198(F) | 功能描述:光纖發射器、接收器、收發器 TOSLINK RECEIVER RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
| TORX198F | 制造商:Toshiba America Electronic Components 功能描述:RX Optical Fiber 6Mbps 6-Pin |
| TORX40 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC RECEIVER |
發布緊急采購，3分鐘左右您將得到回復。