- 您現在的位置：買賣IC網 > PDF目錄373681 > TOTX140 (Toshiba Corporation) FIBER OPTIC TRANSMITTING MODULE PDF資料下載
參數資料
| 型號： | TOTX140 |
| 廠商： | Toshiba Corporation |
| 英文描述： | FIBER OPTIC TRANSMITTING MODULE |
| 中文描述： | 光纖透射模塊 |
| 文件頁數： | 4/6頁 |
| 文件大?。?/td> | 116K |
| 代理商： | TOTX140 |
TOTX140
2001-07-26
4
8. Precautions during use
(
1
)
Maximum rating
The maximum ratings are the limit values which must not be exceeded during operation of device.
None of these rating value must not be exceeded. If the maximum rating value is exceeded, the
characteristics of devices may never be restored properly. In some extreme cases, the device may be
permanently damages.
Lifetime of light emitters
If an optical module is used for a long period of time, degeneration in the characteristics will mostly
be due to a lowering of the fiber output power (Pf) . This is caused by the degradation of the optical
output of the LEDs used as the light source. The cause of degradation of the optical output of the
LEDs may be defects in wafer crystallization or mold resin stress. The detailed causes are, however,
not clear.
The lifetime of light emitters is greatly influenced by the operating conditions and the usage
environment in which it is used as well as by the lifetime characteristics unique to the device type.
Thus, when a light emitting device and its operating conditions determined, Toshiba recommend that
lifetime characteristics be checked.
Depending on the environment conditions, Toshiba recommend that maintenance such as regular
checks of the amount of optical output in accordance with the condition of the operating environment.
Soldering
Optical modules are comprised of internal semiconductor devices. However, in principle, optical
modules are optical components. During soldering, ensure that flux does not contact with the emitting
surface or the detecting surface. Also ensure that proper flux removal is conducted after soldering.
Some optical modules come with a protective cap. The protective cap is used to avoid malfunction
when the optical module is not in use. Note that it is not dust or waterproof.
As mentioned before, optical modules are optical components. Thus, in principle, soldering where
there may be flux residue and flux removal after soldering is not recommended. Toshiba recommend
that soldering be performed without the optical module mounted on the board. Then, after the board
has been cleaned, the optical module should be soldered on to the board manually.
If the optical module cannot be soldered manually, use non
halogen (chlorine
free) flux and make
sure, without cleaning, there is no residue such as chlorine. This is one of the ways to eliminate the
effects of flux. In such a cases, be sure to check the devices’ reliability.
Vibration and shock
This module is plastic sealed and has its wire fixed by resin. This structure is relatively resistant to
vibration and shock. In actual equipment, there are sometimes cases in which vibration, shock, or
stress is applied to soldered parts or connected parts, resulting in lines cut. A care must be taken in
the design of equipment which will be subject to high levels of vibration.
Support pins
The optical transmission module TOTX
1
40 has support pins in order to fix itself to the PCB
temporary. Please make the hole for these pins in the PCB under the condition described in board
layout hole pattern.
Panel attachment
TOTX
1
40 has hole for panel attachment. Please be sure to attach it to panel with self
tapping screw.
Solvent
When using solvent for flux removal, do not use a high acid or high alkali solvent. Be careful not to
pour solvent in to the optical connector ports. If solvent is inadvertently poured in to them, clean it off
using cotton tips.
Protective cap
When the TOTX
1
40 is not in use, attach the protective cap.
Supply voltage
Use the supply voltage within the recommended operating condition (V
CC
= 2.7~3.6 V). Make sure
that supply voltage does not exceed the maximum rating value of 7 V, even for an instant.
(
1
0) Input voltage
If a voltage exceeding the maximum rating value (V
CC
+ 0.5 V) is applied to the transmitter input,
the internal IC may suffer damage. If there is a possibility that excessive voltage due to surges may
be added to the input terminal, insert a protective circuit.
(
11
) Soldering condition
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
Solder at 260°C or less for no more than ten seconds.
相關PDF資料 |
PDF描述 |
|---|---|
| TOTX141P | CONNECTOR ACCESSORY |
| TOTX141 | FIBER OPTIC TRANSMITTING MODULE |
| TOTX170A | FIBER OPTIC TRANSMITTING MODULE |
| TOTX173 | CONNECTOR ACCESSORY |
| TOTX176 | CONNECTOR ACCESSORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TOTX1400(CS) | 制造商:Toshiba America Electronic Components 功能描述:FIBRE OPTIC TRANSMITTER |
| TOTX1400(F) | 功能描述:光纖發射器、接收器、收發器 TOSLNK MOLD SNGL TRNSMTR DATA RATE RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
| TOTX141 | 功能描述:TRANSMITTER MODULE FIBER OPTIC RoHS:否 類別:光電元件 >> 光纖 - 發射器 - 驅動器集成電路 系列:Toslink™ 標準包裝:8 系列:- 波長:- 數據速率:1.6Gbps 功率 - 輸出:- 電源電壓:3.3V 應用:電信 電流 - 電源:- 其它名稱:V23814-U1306IN |
| TOTX141(F) | 制造商:Toshiba 功能描述:TX 制造商:Toshiba 功能描述:TX Cut Tape |
| TOTX141F,T | 功能描述:光纖發射器、接收器、收發器 Toslink Transmitter Board mount 15 Mbps RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
發布緊急采購，3分鐘左右您將得到回復。