參數資料
型號： TPA005D14
廠商： Texas Instruments, Inc.
英文描述： CONNECTOR ACCESSORY
中文描述： 連接器附件
文件頁數： 18/29頁
文件大?。?/td> 420K
代理商： TPA005D14
TPA005D14
2-W STEREO CLASS-D AUDIO POWER AMPLIFIER
SLOS240A – AUGUST 1999 – REVISED MARCH 2000
18
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
efficiency of class-D vs linear operation
Amplifier efficiency is defined as the ratio of output power delivered to the load to power drawn from the supply.
In the efficiency equation below, P
L
is power across the load and P
SUP
is the supply power.
P
L
P
SUP
Efficiency
A high-efficiency amplifier has a number of advantages over one with lower efficiency. One of these advantages
is a lower power requirement for a given output, which translates into less waste heat that must be removed
from the device, smaller power supply required, and increased battery life.
Audio power amplifier systems have traditionally used linear amplifiers, which are well known for being
inefficient. Class-D amplifiers were developed as a means to increase the efficiency of audio power amplifier
systems.
A linear amplifier is designed to act as a variable resistor network between the power supply and the load. The
transistors operate in their linear region and voltage that is dropped across the transistors (in their role as
variable resistors) is lost as heat, particularly in the output transistors.
The output transistors of a class-D amplifier switch from full OFF to full ON (saturated) and then back again,
spending very little time in the linear region in between. As a result, very little power is lost to heat because the
transistors are not operated in their linear region. If the transistors have a low ON resistance, little voltage is
dropped across them, further reducing losses. The ideal class-D amplifier is 100% efficient, which assumes that
both the ON resistance (r
DS(ON)
) and the switching times of the output transistors are zero.
the ideal class-D amplifier
To illustrate how the output transistors of a class-D amplifier operate, a half-bridge application is examined first
(Figure 21).
VDD
VOUT
L
CL
RL
IL
IOUT
+
–
VA
M2
M1
C
Figure 21. Half-Bridge Class-D Output Stage
Figures 22 and 23 show the currents and voltages of the half-bridge circuit. When transistor M1 is on and M2
is off, the inductor current is approximately equal to the supply current. When M2 switches on and M1 switches
off, the supply current drops to zero, but the inductor keeps the inductor current from dropping. The additional
inductor current is flowing through M2 from ground. This means that V
A
(the voltage at the drain of M2, as shown
in Figure 21) transitions between the supply voltage and slightly below ground. The inductor and capacitor form
a low-pass filter, which makes the output current equal to the average of the inductor current. The low pass filter
averages V
A
, which makes V
OUT
equal to the supply voltage multiplied by the duty cycle.
相關PDF資料
PDF描述
TPA005D14DCA 2-W STEREO CLASS-D AUDIO POWER AMPLIFIER
TPA005D12DCAR Amplifier. Other
TPA005D14DCAR Amplifier. Other
TPA0112PWPR AUDIO AMPLIFIER|DUAL|CMOS|TSSOP|24PIN|PLASTIC
TPA0132PWPR AUDIO AMPLIFIER|DUAL|CMOS|TSSOP|24PIN|PLASTIC
相關代理商/技術參數
參數描述
TPA005D14DCA 功能描述:音頻放大器 2W Stereo P RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA005D14DCAR 制造商:TI 制造商全稱:Texas Instruments 功能描述:Amplifier. Other
TPA00NBNF10 制造商:GREATECS 制造商全稱:GREATECS 功能描述:SPST SMT Tactile Switches with LED
TPA00NBNG10 制造商:GREATECS 制造商全稱:GREATECS 功能描述:SPST SMT Tactile Switches with LED
TPA00NBRB10 制造商:GREATECS 制造商全稱:GREATECS 功能描述:SPST SMT Tactile Switches with LED
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*