參數資料
型號： TPA0152PWP
廠商： TEXAS INSTRUMENTS INC
元件分類： 音頻控制
英文描述： 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24
封裝： GREEN, PLASTIC, HTSSOP-24
文件頁數： 15/32頁
文件大?。?/td> 651K
代理商： TPA0152PWP
www.ti.com
RL
C(C)
VO(PP)
VDD
3 dB
fc
Single-Ended Operation
BTL AMPLIFIER EFFICIENCY
V(LRMS)
VO
IDD
IDD(avg)
TPA0152
SLOS246F – JUNE 1999 – REVISED SEPTEMBER 2004
Figure 36. Single-Ended Configuration and Frequency Response
Increasing power to the load does carry a penalty of increased internal power dissipation. The increased
dissipation is understandable, since the BTL configuration produces 4
× the output power of the SE configuration.
Internal dissipation versus output power is discussed further in the Crest Factor and Thermal Considerations
section.
In SE mode (see Figure 36), the load is driven from the primary amplifier output for each channel (LOUT+ and
ROUT+).
The amplifier switches to single-ended operation when the SE/BTL terminal is held high. This puts the negative
outputs in a high-impedance state, and reduces the amplifier's gain by 6 dB.
Class-AB amplifiers are inefficient, primarily because of voltage drop across the output-stage transistors. The two
components of the internal voltage drop are the headroom or dc voltage drop that varies inversely to output
power, and the sine wave nature of the output. The total voltage drop can be calculated by subtracting the RMS
value of the output voltage from VDD. The internal voltage drop multiplied by the RMS value of the supply current
(IDDrms) determines the internal power dissipation of the amplifier.
An easy-to-use equation to calculate efficiency begins as the ratio of power from the power supply to the power
delivered to the load. To accurately calculate the RMS and average values of power in the load and in the
amplifier, the current and voltage waveforms must be understood (see Figure 37).
Figure 37. Voltage and Current Waveforms for BTL Amplifiers
Although the voltages and currents for SE and BTL are sinusoidal in the load, currents from the supply are very
different between SE and BTL configurations. In an SE application, the current waveform is a half-wave rectified
shape, whereas in BTL it is a full-wave rectified waveform. Therefore, RMS conversion factors are different. Keep
in mind that for most of the waveform both the push and pull transistors are not on at the same time, which
supports the fact that each amplifier in the BTL device only draws current from the supply for half the waveform.
Equation 8 and Equation 9 are the basis for calculating amplifier efficiency.
22
相關PDF資料
PDF描述
TPA0152PWPRG4 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24
TPA0152PWPG4 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24
TPA0162PWPR 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24
TPA0162PWP 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24
TPA0162PWPRG4 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24
相關代理商/技術參數
參數描述
TPA0152PWPG4 功能描述:音頻放大器 2W Stereo A RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA0152PWPR 功能描述:音頻放大器 St 2W Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA0152PWPRG4 功能描述:音頻放大器 St 2W Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA0162 制造商:TI 制造商全稱:Texas Instruments 功能描述:2-W STEREO AUDIO POWER AMPLIFIER WITH DIGITAL VOLUME CONTROL
TPA0162EVM 功能描述:音頻 IC 開發工具 TPA0162 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*