參數資料
型號： TPA0152PWPR
元件分類： 運動控制電子
英文描述： Dual Audio Amplifier
中文描述： 雙音頻放大器
文件頁數： 26/34頁
文件大?。?/td> 488K
代理商： TPA0152PWPR
TPA0112
2-W STEREO AUDIO POWER AMPLIFIER
WITH FOUR SELECTABLE GAIN SETTINGS
SLOS204B – MAY 1999 – REVISED MARCH 2000
26
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
Increasing power to the load does carry a penalty of increased internal power dissipation. The increased
dissipation is understandable considering that the BTL configuration produces 4
×
the output power of the SE
configuration. Internal dissipation versus output power is discussed further in the crest factor and thermal
considerationssection.
single-ended operation
In SE mode (see Figure 44 and Figure 45), the load is driven from the primary amplifier output for each channel
(OUT+, terminals 21 and 4).
The amplifier switches single-ended operation when the SE/BTL terminal is held high. This puts the negative
outputs in a high-impedance state, and reduces the amplifier’s gain to 1 V/V.
BTL amplifier efficiency
Class-AB amplifiers are notoriously inefficient. The primary cause of these inefficiencies is voltage drop across
the output stage transistors. There are two components of the internal voltage drop. One is the headroom or
dc voltage drop that varies inversely to output power. The second component is due to the sinewave nature of
the output. The total voltage drop can be calculated by subtracting the RMS value of the output voltage from
V
DD
. The internal voltage drop multiplied by the RMS value of the supply current, I
DD
rms, determines the internal
power dissipation of the amplifier.
An easy-to-use equation to calculate efficiency starts out as being equal to the ratio of power from the power
supply to the power delivered to the load. To accurately calculate the RMS and average values of power in the
load and in the amplifier, the current and voltage waveform shapes must first be understood (see Figure 46).
V(LRMS)
VO
IDD
IDD(avg)
Figure 46. Voltage and Current Waveforms for BTL Amplifiers
Although the voltages and currents for SE and BTL are sinusoidal in the load, currents from the supply are very
different between SE and BTL configurations. In an SE application the current waveform is a half-wave rectified
shape whereas in BTL it is a full-wave rectified waveform. This means RMS conversion factors are different.
Keep in mind that for most of the waveform both the push and pull transistors are not on at the same time, which
supports the fact that each amplifier in the BTL device only draws current from the supply for half the waveform.
The following equations are the basis for calculating amplifier efficiency.
相關PDF資料
PDF描述
TPA0162PWPR AUDIO AMPLIFIER|DUAL|CMOS|TSSOP|24PIN|PLASTIC
TPA0122PWP CONNECTOR ACCESSORY
TPA0312PWPR SWITCH, DPDT, R/A, PCB, ON-OFF-ON; Switch function type:On-Off-On; Material, contact:Copper Alloy; Temp, op. max:85(degree C); Temp, op. min:-30(degree C); Length / Height, external:9.14mm; Width, external:8.13mm; Depth, RoHS Compliant: Yes
TPA032D02DCAR Dual Audio Amplifier
TPA100RL SINGLE BIDIRECTIONAL BREAKOVER DIODE|133V V(BO) MAX|800MA I(S)|DO-204AC
相關代理商/技術參數
參數描述
TPA0152PWPRG4 功能描述:音頻放大器 St 2W Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA0162 制造商:TI 制造商全稱:Texas Instruments 功能描述:2-W STEREO AUDIO POWER AMPLIFIER WITH DIGITAL VOLUME CONTROL
TPA0162EVM 功能描述:音頻 IC 開發工具 TPA0162 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
TPA0162PWP 功能描述:音頻放大器 2W Stereo A RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA0162PWPG4 功能描述:音頻放大器 2W Stereo A RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*