參數資料
型號： TPA3003D2PFBRG4
廠商： TEXAS INSTRUMENTS INC
元件分類： 音頻控制
英文描述： 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48
封裝： GREEN, PLASTIC, TQFP-48
文件頁數： 13/36頁
文件大小： 755K
代理商： TPA3003D2PFBRG4
TPA3003D2
SLOS406A FEBRUARY 2003 REVISED MARCH 2003
20
www.ti.com
APPLICATION INFORMATION
FADE operation
The FADE terminal is a logic input that controls the operation of the volume control circuitry during transitions
to and from the shutdown state and during power-up.
A logic low on this terminal places the amplifier in the fade mode. During power-up or recovery from the
shutdown state (a logic high is applied to the SD terminal), the volume is smoothly ramped up from the mute
state, 75 dB, to the desired volume setting determined by the voltage on the volume control terminal.
Conversely, the volume is smoothly ramped down from the current state to the mute state when a logic low is
applied to the SD terminal. The timing of the volume control circuitry is controlled by an internal 60-Hz clock.
This clock determines the rate at which the gain changes when adjusting the voltage on the external volume
control pins. The gain updates every 4 clock cycles (nominally 67 ms based on a 60 Hz clock) to the next step
until the final desired gain is reached. For example, if the TPA3003D2 is currently in the +0.53 dB class-D gain
step and the VOLUME pin is adjusted for maximum gain at +36 dB, the time required for the gain to reach 36
dB is 14 steps x 67 ms/step = 0.938 seconds. Referencing Table 1, there are 14 steps between the +0.53 dB
gain step and the maximum gain step of +36 dB.
Figure 27 shows a scope capture of the differential output (measured across OUT+ and OUT) with the amplifier
in the fade mode. A 1 Vpp dc voltage was applied across the differential inputs and a logic low was applied to
the SD terminal at the time defined in the figure. The figure depicts the outputs transitioning from one gain step
to the next lower step at approximately 67 ms/step.
A logic high on this pin disables the volume fade effect during transitions to and from the shutdown state and
during power-up. During power-up or recovery from the shutdown state (a logic high is applied to the SD
terminal), the transition from the mute state, 75 dB, to the desired volume setting is less than 1 ms. Conversely,
the volume ramps down from current state to the mute state within 1 ms when a logic low is applied to the SD
terminal.
Figure 28 shows a scope capture of the differential output with the fade effect disabled. The outputs transition
to the lowest gain state within 1ms of applying a logic low to the SD terminal.
SD = 0V
GND
Figure 27. Differential Output With FADE (Terminal 30) Held Low
相關PDF資料
PDF描述
TPA3003D2PFBG4 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48
TPA3004D2PHPRG4 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48
TPA3004D2PHPG4 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48
TPA3005D2PHPR 6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48
TPA3005D2PHP 6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48
相關代理商/技術參數
參數描述
TPA3004 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-W STEREO CLASS-D AUDIO POWER AMPLIFIER WITH DC VOLUME CONTROL
TPA3004D2 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-W STEREO CLASS-D AUDIO POWER AMPLIFIER WITH DC VOLUME CONTROL
TPA3004D2_07 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-W STEREO CLASS-D AUDIO POWER AMPLIFIER WITH DC VOLUME CONTROL
TPA3004D2EVM 功能描述:音頻 IC 開發工具 TPA3004D2 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
TPA3004D2PHP 功能描述:音頻放大器 Stereo Hi-Pwr Filter-Free Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*