參數(shù)資料
型號: TPA3106D1VFPG4
廠商: TEXAS INSTRUMENTS INC
元件分類: 音頻/視頻放大
英文描述: 40 W, 1 CHANNEL, AUDIO AMPLIFIER, PQFP32
封裝: 7 X 7 MM, GREEN, PLASTIC, HLQFP-32
文件頁數(shù): 20/35頁
文件大?。?/td> 1250K
代理商: TPA3106D1VFPG4
www.ti.com
CLASS-D RC LOW-PASS FILTER
R
FILT
R
L
R
FILT
C
FILT
V
L=VIN
V
OUT
R
ANA
C
ANA
R
ANA
C
ANA
C
FILT
To APA
GND
AP AnalyzerInput
RCLow-PassFilters
Load
V
OUT
w
V
IN
wO
R
ANA + RFILT
R
ANA
1+j
(
)
=
(5)
f =
c
2 x f
max
(6)
SLOS516B – OCTOBER 2007 – REVISED MARCH 2007
An RC filter is used to reduce the square-wave output when the analyzer inputs cannot process the pulse-width
modulated class-D output waveform. This filter has little effect on the measurement accuracy because the cutoff
frequency is set above the audio band. The high frequency of the square wave has negligible impact on
measurement accuracy because it is well above the audible frequency range, and the speaker cone cannot
respond at such a fast rate. The RC filter is not required when an LC low-pass filter is used, such as with the
class-D APAs that employ the traditional modulation scheme (TPA032D0x, TPA005Dxx).
The component values of the RC filter are selected using the equivalent output circuit as shown in Figure 36. RL
is the load impedance that the APA is driving for the test. The analyzer input impedance specifications should be
available and substituted for RANA and CANA. The filter components, RFILT and CFILT, can then be derived for the
system. The filter should be grounded to the APA near the output ground pins or at the power supply ground pin
to minimize ground loops.
Figure 36. Measurement Low-Pass Filter Derivation Circuit-Class-D APAs
The transfer function for this circuit is shown in Equation 5 where
ω
O = REQCEQ, REQ = RFILT || RANA and
CEQ = (CFILT + CANA). The filter frequency should be set above fMAX, the highest frequency of the measurement
bandwidth, to avoid attenuating the audio signal. Equation 6 provides this cutoff frequency, fC. The value of RFILT
must be chosen large enough to minimize current that is shunted from the load, yet small enough to minimize the
attenuation of the analyzer-input voltage through the voltage divider formed by RFILT and RANA. A general rule is
that RFILT should be small (~100 ) for most measurements. This reduces the measurement error to less than
1% for RANA ≥ 10 k.
An exception occurs with the efficiency measurements, where RFILT must be increased by a factor of ten to
reduce the current shunted through the filter. CFILT must be decreased by a factor of ten to maintain the same
cutoff frequency. See Table 3 for the recommended filter component values.
Once fC is determined and RFILT is selected, the filter capacitance is calculated. When the calculated value is not
available, it is better to choose a smaller capacitance value to keep fC above the minimum desired value
calculated in Equation 7.
Copyright 2007, Texas Instruments Incorporated
27
Product Folder Link(s): TPA3106D1
相關PDF資料
PDF描述
TPA3106D1VFPRG4 40 W, 1 CHANNEL, AUDIO AMPLIFIER, PQFP32
TPA3106D1VFPR 40 W, 1 CHANNEL, AUDIO AMPLIFIER, PQFP32
TPA3106D1VFP 40 W, 1 CHANNEL, AUDIO AMPLIFIER, PQFP32
TPA3107D2PAPR 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64
TPA3107D2PAPT 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64
相關代理商/技術參數(shù)
參數(shù)描述
TPA3106D1VFPR 功能描述:音頻放大器 40W Mono Class-D Audio Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA3106D1VFPR 制造商:Texas Instruments 功能描述:Audio Power Amplifiers
TPA3106D1VFPRG4 功能描述:音頻放大器 40W Mono Class-D Audio Power Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA3107D2 制造商:TI 制造商全稱:Texas Instruments 功能描述:15-W STEREO CLASS-D AUDIO POWER AMPLIFIER
TPA3107D2_07 制造商:TI 制造商全稱:Texas Instruments 功能描述:15-W STEREO CLASS-D AUDIO POWER AMPLIFIER