參數資料
型號: TPA3121D2PWPG4
廠商: TEXAS INSTRUMENTS INC
元件分類: 音頻/視頻放大
英文描述: AUDIO AMPLIFIER, PDSO24
封裝: PLASTIC, HTSSOP-24
文件頁數: 16/29頁
文件大?。?/td> 860K
代理商: TPA3121D2PWPG4
DIFFERENTIAL INPUT AND BTL OUTPUT (TPA3121D2 Mono Configuration)
C
IN
AudioPower
Amplifier
Generator
C
IN
R
GEN
R
GEN
R
IN
R
IN
V
GEN
Analyzer
R
ANA
R
ANA
C
ANA
R
L
C
ANA
Twisted-PairWire
EvaluationModule
Twisted-PairWire
Lfilt
Cfilt
www.ti.com........................................................................................................................................................................................................ SLOS537 – MAY 2008
Many of the class-D APAs and many class-AB APAs have differential inputs and bridge-tied-load (BTL) outputs.
Differential inputs have two input pins per channel and amplify the difference in voltage between the pins.
Differential inputs reduce the common-mode noise and distortion of the input circuit. BTL is a term commonly
used in audio to describe differential outputs. BTL outputs have two output pins providing voltages that are 180
°
out of phase. The load is connected between these pins. This has the added benefits of quadrupling the output
power to the load and eliminating a dc-blocking capacitor.
A block diagram of the measurement circuit is shown in Figure 36. The differential input is a balanced input,
meaning the positive (+) and negative (–) pins have the same impedance to ground. Similarly, the SE output
equates to a balanced output.
Figure 36. Differential Input, BTL Output Measurement Circuit
The generator should have balanced outputs, and the signal should be balanced for best results. An unbalanced
output can be used, but it may create a ground loop that affects the measurement accuracy. The analyzer must
also have balanced inputs for the system to be fully balanced, thereby cancelling out any common-mode noise in
the circuit and providing the most accurate measurement.
The following general rules should be followed when connecting to APAs with differential inputs and BTL outputs:
Use a balanced source to supply the input signal.
Use an analyzer with balanced inputs.
Use twisted-pair wire for all connections.
Use shielding when the system environment is noisy.
Ensure that the cables from the power supply to the APA, and from the APA to the load, can handle the large
currents (see Table 5).
Table 5 shows the recommended wire size for the power supply and load cables of the APA system. The real
concern is the dc or ac power loss that occurs as the current flows through the cable. These recommendations
are based on 12-inch (30.5-cm)-long wire with a 20-kHz sine-wave signal at 25
°C.
Table 5. Recommended Minimum Wire Size for Power Cables
DC POWER LOSS
AC POWER LOSS
POUT (W)
RL()
AWG Size
(mW)
10
4
18
22
16
40
18
42
2
4
18
22
3.2
8
3.7
8.5
1
8
22
28
2
8
2.1
8.1
< 0.75
8
22
28
1.5
6.1
1.6
6.2
Copyright 2008, Texas Instruments Incorporated
23
Product Folder Link(s): TPA3121D2
相關PDF資料
PDF描述
TPA3121D2PWPRG4 AUDIO AMPLIFIER, PDSO24
TPA3121D2PWP AUDIO AMPLIFIER, PDSO24
TPA3121D2PWPR AUDIO AMPLIFIER, PDSO24
TPA3122D2N 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP20
TPA3123D2PWPG4 25 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO24
相關代理商/技術參數
參數描述
TPA3121D2PWPR 功能描述:音頻放大器 15W Stereo Class-D Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA3121D2PWPRG4 功能描述:音頻放大器 15W Stereo Class-D Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA3122D2 制造商:TI 制造商全稱:Texas Instruments 功能描述:15-W STEREO CLASS-D AUDIO POWER AMPLIFIER
TPA3122D2EVM 功能描述:音頻 IC 開發工具 TPA3122D2EVM Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
TPA3122D2N 功能描述:音頻放大器 15W STEREO CLASS-D AUDIO POWER AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel