參數資料
型號： TPA3124D2PWPRG4
廠商： TEXAS INSTRUMENTS INC
元件分類： 音頻／視頻放大
英文描述： AUDIO AMPLIFIER, PDSO24
封裝： PLASTIC, HTSSOP-24
文件頁數： 5/29頁
文件大?。?/td> 859K
代理商： TPA3124D2PWPRG4
Gain Setting via GAIN0 and GAIN1 Inputs
INPUT RESISTANCE
Ci
IN
Zi
Zf
Input
Signal
f=
1
2
Z C
p
i
(1)
www.ti.com........................................................................................................................................................................................................ SLOS578 – MAY 2008
Several things can be done to relieve power-supply pumping. The lowest impact is to operate the two inputs out
of phase 180
° and reverse the speaker connections. Because most audio is highly correlated, this causes the
supply pumping to be out of phase and not as severe. If this is not enough, the amount of bulk capacitance on
the supply must be increased. Also, improvement is realized by hooking other supplies to this node, thereby,
sinking some of the excess current. Power-supply pumping should be tested by operating the amplifier at low
frequencies and high output levels.
The gain of the TPA3124D2 is set by two input terminals, GAIN0 and GAIN1.
The gains listed in Table 2 are realized by changing the taps on the input resistors and feedback resistors inside
the amplifier. This causes the input impedance (ZI) to be dependent on the gain setting. The actual gain settings
are controlled by ratios of resistors, so the gain variation from part-to-part is small. However, the input impedance
from part-to-part at the same gain may shift by ±20% due to shifts in the actual resistance of the input resistors.
For design purposes, the input network (discussed in the next section) should be designed assuming an input
impedance of 8 k
, which is the absolute minimum input impedance of the TPA3124D2. At the higher gain
settings, the input impedance could increase as high as 72 k
.
Table 2. Gain Setting
INPUT IMPEDANCE
AMPLIFIER GAIN (dB),
GAIN1
GAIN0
(k
),
TYPICAL
0
20
60
0
1
26
30
1
0
32
15
1
36
9
Changing the gain setting can vary the input resistance of the amplifier from its smallest value, 10 k
±20%, to
the largest value, 60 k
±20%. As a result, if a single capacitor is used in the input high-pass filter, the –3-dB
cutoff frequency may change when changing gain steps.
The –3-dB frequency can be calculated using Equation 1. Use the ZI values given in Table 2.
Copyright 2008, Texas Instruments Incorporated
13
Product Folder Link(s): TPA3124D2
相關PDF資料
PDF描述
TPA3124D2PWPR AUDIO AMPLIFIER, PDSO24
TPA3124D2PWP AUDIO AMPLIFIER, PDSO24
TPA3125D2N 36 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP20
TPA3200D1DCP 12.8 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO44
TPA3200D1DCPR 12.8 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO44
相關代理商/技術參數
參數描述
TPA3125D2 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-W STEREO CLASS-D AUDIO POWER AMPLIFIER
TPA3125D2EVM 功能描述:音頻 IC 開發工具 TPA3125D2EVM Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
TPA3125D2N 功能描述:音頻放大器 10W Stereo Class-D Audio Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA3128D2DAP 功能描述:IC AUDIO AMP CLASS D 32HTSSOP 制造商:texas instruments 系列:- 包裝:管件 零件狀態:在售 類型:D 類 輸出類型:2 通道（立體聲） 不同負載時的最大輸出功率 x 通道數:30W x 2 @ 8 歐姆 電壓 - 電源:4.5 V ~ 26 V 特性:短路保護 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C（TA） 供應商器件封裝:32-HTSSOP 封裝/外殼:32-TSSOP（0.240"，6.10mm 寬）裸露焊盤 標準包裝:46
TPA3128D2DAPR 功能描述:IC AUDIO AMP CLASS D 32-HTSSOP 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:在售 類型:D 類 輸出類型:2 通道（立體聲） 不同負載時的最大輸出功率 x 通道數:30W x 2 @ 8 歐姆 電壓 - 電源:4.5 V ~ 26 V 特性:短路保護 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C（TA） 供應商器件封裝:32-HTSSOP 封裝/外殼:32-TSSOP（0.240"，6.10mm 寬）裸露焊盤 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*