- 您現在的位置：買賣IC網 > PDF目錄11788 > TPFLXIC016 (Microchip Technology)IC MICROCONTROLLER PDF資料下載
參數資料
| 型號： | TPFLXIC016 |
| 廠商： | Microchip Technology |
| 文件頁數： | 10/10頁 |
| 文件大小： | 0K |
| 描述： | IC MICROCONTROLLER |
| 標準包裝： | 1 |
| 系列： | * |
p9 of 10
26-Aug-10
USB-FileSys / USB-Config
HW149-8
www.hexwax.com
With the 20-pin device, the next two bytes are the
number of bytes to write, up to a maximum of 64. The
write must not cross the 64-byte sector boundary.
Once the command has been sent, a response byte will
be received. Assuming this the Success response 0x00,
the data bytes are then sent. A second response byte
will then be received.
Note: Writes to files are permitted even if the read-only
bit is set in their directory entry; writes after the end of
the existing file may cause further clusters to be
allocated to the file.
Example:
Command: Write 4 bytes at position 0123 on file
handle 02
0E 02 23 01 00 00 04 00
Response:
Success, data is 12 34 56 78.
00
Data:
(01 02 03 04)
01 02 03 04
Response:
Success.
00
Get Info
This command reads device information. The command
is the byte 0x0F. The first byte of the response is the
status byte. The second bytes indicates the information
in table 8. The third and fourth bytes are the version
number, least significant byte first.
Example:
Command: Get Info
0F
Response:
Success, device is 500mA with a 4096-
byte cluster size, version 0001
00 61 01 00
Table 8. Info Flags
Bit
Meaning
0
Maximum current draw:
0: Draw a maximum of 100mA from USB (default)
1: Draw a maximum of 500mA from USB
2-1
Activity pin function:
00: High for 100ms on any USB activity
10: High on PC write to any sector
11: High on PC write to root directory entry
5-7
Cluster size:
000 - 512 bytes
001 - 1024 bytes
010 - 2048 bytes
011 - 4096 bytes
100 - 8192 bytes
101 - 16384 bytes
110 - 32768 bytes
(Read only – ignored with Set Info command)
Set Info
This command sets the maximum current the device
may draw from the PC, and the function of the Activity
pin. The first byte of the command is the value 0x10.
The second is as specified in table 8. The response is
the status byte.
If USB-FileSys is configured for 500mA current draw, it
will only work when plugged directly into PCs and
powered hubs. The setting takes effect from the next
plug-in. In any event, the no more than 100μA should
be drawn if the PTO# pin is high.
Example:
Command: Set 500mA operation, activity on write
10 05
Response:
Success.
00
Delivery and Programming
USB-FileSys is generally distributed in pre-programmed
in 28-pin DIL and 20-pin SSOP packages. Contact us
for other package options.
In high volumes (5K+), USB-FileSys is available reeled
with your custom settings preloaded, in any available
package.
TEAclipper Programming
For programming the firmware using TEAclipper/PIC HV,
the PGC, PGD and Vpp pins must be accessible.
During programming, these pins must be protected
against contention.
In particular, note that Vpp is
subject to up to 13V during programming. Nothing else
should be connected to Vpp except via a 22k pull-up
resistor.
The TEAclipper connector format is shown in figure 9.
Since the programming time is very fast,
no
programming socket is required. The TEAclipper can be
‘leaned’ against the plate-through holes shown.
It is strongly recommended that this connector is
included in circuits even if in-circuit programming is not
anticipated, since this allows you to upgrade the
firmware if necessary.
1mm hole dia
2.54mm spacing
Pin 1 indicated
by square pad
P
G
D
P
G
C
V
pp
V
ss
V
dd
Figure 9. Recommended plate-through connector design
Evaluation Board
The USB-Eval evaluation board is available for
evaluating USB-FileSys. Due to the variety of potential
implementations it is supplied unpopulated and a
prototyping area is provided. This will be necessary for
SD memory implementation. (e.g. Figure 10.)
相關PDF資料 |
PDF描述 |
|---|---|
| TPFLXIC014 | IC MICROCONTROLLER |
| 556137-4 | CONN HOUSING 1 POS RED |
| 556137-2 | CONN HOUSING 1 POS BLK |
| 1445957-5 | CONN HOUSING POWER 1POS RED |
| V72C28H150BG2 | CONVERTER MOD DC/DC 28V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPFLXIC017 | 功能描述:插座和適配器 USB-FileSys-SS FlexiPanel RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x |
| TPFLXIC018 | 功能描述:插座和適配器 Access-Touch-SS FlexiPanel RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x |
| TP-FUEL-0.250 | 功能描述:LABEL IDENTIFICATION TAPE RoHS:否 類別:計算機，辦公室 - 元件，配件 >> 標簽，標記 系列:TP-帶 標準包裝:1 系列:PANACEA™ 類型:標簽 標簽類型:熱敏式 標簽尺寸:0.75" x 26.2'（19.1mm x 8.0m） 材質:聚酯 顏色:透明 適用于相關產品:熱敏打印機 包裝:卷 其它名稱:298-1346 |
| TP-FUEL-0.375 | 功能描述:LABEL IDENTIFICATION TAPE RoHS:是 類別:計算機，辦公室 - 元件，配件 >> 標簽，標記 系列:TP-帶 標準包裝:1 系列:PANACEA™ 類型:標簽 標簽類型:熱敏式 標簽尺寸:0.75" x 26.2'（19.1mm x 8.0m） 材質:聚酯 顏色:透明 適用于相關產品:熱敏打印機 包裝:卷 其它名稱:298-1346 |
| TP-FUEL-0.500 | 功能描述:LABEL IDENTIFICATION TAPE RoHS:否 類別:計算機，辦公室 - 元件，配件 >> 標簽，標記 系列:TP-帶 標準包裝:1 系列:PANACEA™ 類型:標簽 標簽類型:熱敏式 標簽尺寸:0.75" x 26.2'（19.1mm x 8.0m） 材質:聚酯 顏色:透明 適用于相關產品:熱敏打印機 包裝:卷 其它名稱:298-1346 |
發布緊急采購，3分鐘左右您將得到回復。