- 您現在的位置：買賣IC網 > PDF目錄68612 > TPS2211APWG4 (TEXAS INSTRUMENTS INC) 3-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 PDF資料下載
參數資料
| 型號： | TPS2211APWG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 3-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| 封裝： | GREEN, PLASTIC, TSSOP-20 |
| 文件頁數： | 6/25頁 |
| 文件大小： | 580K |
| 代理商： | TPS2211APWG4 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁
TPS2211A
SINGLESLOT PC CARD POWER INTERFACE SWITCH
FOR PARALLEL PCMCIA CONTROLLERS
SLVS282B SEPTEMBER 2000 REVISED JULY 2005
14
WWW.TI.COM
APPLICATION INFORMATION
12-V supply not required
Most PC Card switches use the externally supplied 12 V to power gate drive and other chip functions, which
require that power be present at all times. The TPS2211A offers considerable power savings by using an internal
charge pump to generate the required higher voltages from the 5-V input. Therefore, the external 12-V supply
can be disabled except when needed for flash-memory functions, thereby extending battery lifetime. Do not
ground the 12-V switch inputs when the 12-V input is not used. Additional power savings are realized by the
TPS2211A during a software shutdown, in which quiescent current drops to a maximum of 1
A.
3.3-V low-voltage mode
The TPS2211A operates in a 3.3-V low-voltage mode when 3.3 V is the only available input voltage
(VI(5V) = 0). This allows host and PC Cards to be operated in low-power 3.3-volts-only modes such as sleep or
pager modes. Note that in these operation modes, the TPS2211A derives its bias current from the 3.3-V input
pin and only 3.3 V can be delivered to the PC Card.
voltage transitioning requirement
PC Cards are migrating from 5 V to 3.3 V to minimize power consumption, optimize board space, and increase
logic speeds. The TPS2211A meets all combinations of power delivery as currently defined in the PCMCIA
standard. The latest protocol accommodates mixed 3.3-V/5-V systems by first powering the card with 5 V, then
polling it to determine its 3.3-V compatibility. The PCMCIA specification requires that the capacitors on 3.3-V
compatible cards be discharged to below 0.8 V before applying 3.3-V power. This functions as a power reset
and ensures that sensitive 3.3-V circuitry is not subjected to any residual 5-V charge. The TPS2211A offers a
selectable VCC and Vpp ground state, in accordance with PCMCIA 3.3-V/5-V switching specifications.
output ground switches
PC Card specification requires that VCC be discharged within 100 ms. PC Card resistance can not be relied on
to provide a discharge path for voltages stored on PC Card capacitance because of possible high-impedance
isolation by power-management schemes.
power-supply considerations
The TPS2211A has multiple pins for each of its 3.3-V and 5-V power inputs and for the switched AVCC outputs.
Any individual pin can conduct the rated input or output current. Unless all pins are connected in parallel, the
series resistance is significantly higher than that specified, resulting in increased voltage drops and lost power.
It is recommended that all input and output power pins be paralleled for optimum operation.
To increase the noise immunity of the TPS2211A, the power supply inputs should be bypassed with a 4.7-
F,
or larger, electrolytic or tantalum capacitor paralleled by a 0.1-
F ceramic capacitor. It is strongly recommended
that the switched outputs be bypassed with a 0.1-
F, or larger, ceramic capacitor; doing so improves the
immunity of the TPS2211A to electrostatic discharge (ESD). Care should be taken to minimize the inductance
of PCB traces between the TPS2211A and the load. High switching currents can produce large negative voltage
transients, which forward biases substrate diodes, resulting in unpredictable performance. Similarly, no pin
should be taken below 0.3 V.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2211APWR | 3-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| TPS2211AIDBR | 3-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| TPS22921YZPR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA6 |
| TPS22922BYFPR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA6 |
| TPS22922BYZPR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2211APWP | 功能描述:熱插拔功率分布 PCMCIA Pwr Intfce Sw RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2211APWPG4 | 功能描述:熱插拔功率分布 1A Sngl-Slot PC Card Power Switch RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2211APWPR | 功能描述:熱插拔功率分布 1A Sngl-Slot PC Card Power Switch RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2211APWPRG4 | 功能描述:熱插拔功率分布 1A Sngl-Slot PC Card Power Switch RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2211APWR | 功能描述:熱插拔功率分布 1A Sgl-Slot PC Card Power Sw RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。