- 您現在的位置：買賣IC網 > PDF目錄98279 > TPS2346PWG4 (TEXAS INSTRUMENTS INC) 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 PDF資料下載
參數資料
| 型號： | TPS2346PWG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 |
| 封裝： | GREEN, TSSOP-24 |
| 文件頁數： | 20/30頁 |
| 文件大?。?/td> | 490K |
| 代理商： | TPS2346PWG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
TPS2346
SLUS529 – MAY 2002
27
www.ti.com
APPLICATION INFORMATION
layout considerations
To optimize the performance of the TPS2346, care should be taken to use good layout practice with the parts
placement and etch routing of the hot swap circuit components. This includes any protection devices as well
as the sense and pass elements. Protection devices should be located close to the hot swap controller, and
trace-lengths back to their respective pins kept to a minimum. If a decoupling capacitor is used on the VIN1
supply, it also should be placed close to the part.
Mount the charge pump reservoir capacitor (C6 in the application diagram) close to the TPS2346, with minimal
trace lengths back to the CPUMP and CPGND pins.
For proper operation, the three ground pins of the TPS2346 must be connected together near the device. The
ground leads of the ramp and charge pump capacitors, protection diodes, and any decoupling capacitors should
also tie into this node close to the part. This junction should be routed separately back to the J1 connector, where
it can tie into the PCB GND node, as opposed to tying into the ground plane elsewhere in the high-current return
path.
Use wide traces when connecting the sense resistors and power FETs into their respective current paths. When
feeding these connections through from an internal power plane, use multiple vias to reduce the overall
impedance of the current path. This helps reduce insertion loss across the hot swap interface, and improve the
thermal performance of the PCB. Additional copper plane used on the land patterns of these devices can
significantly reduce their thermal impedance, reducing temperature rise in the module and improving overall
reliability of the power devices.
Connections to the sense resistors for the VINx and CSx device pins should be made with good Kelvin
connections to optimize the accuracy of the current-limit thresholds and slew-rate control. This is especially
important on high-current supplies. When typical load levels on these supplies are high, board trace resistance
between elements in the supply current paths becomes significant. The two sense traces for each supply should
connect symmetrically to the sense resistor land pattern, in close proximity to the element leads, and not
upstream or downstream from the device. Trace routing back to the TPS2346 should be fairly well balanced.
Figure 22 illustrates two recommendations for the current sense layout.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2350DRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| TPS2350PWG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| TPS2359RHHT | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC36 |
| TPS2363PFBRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48 |
| TPS2363PFBG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2346PWR | 功能描述:熱插拔功率分布 Optical Network Hot Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2346PWRG4 | 功能描述:熱插拔功率分布 Optical Network Hot Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2350D | 功能描述:熱插拔功率分布 Pwr Mngr for Redund -48V Supplies RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2350DG4 | 功能描述:熱插拔功率分布 Pwr Mngr for Redund -48V Supplies RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2350DR | 功能描述:熱插拔功率分布 Pwr Mngr for Redund -48V Supplies RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。