- 您現在的位置：買賣IC網 > PDF目錄98279 > TPS2370PW (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 PDF資料下載
參數資料
| 型號： | TPS2370PW |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | GREEN, PLASTIC, TSSOP-8 |
| 文件頁數： | 15/17頁 |
| 文件大?。?/td> | 426K |
| 代理商： | TPS2370PW |
TPS2370
SLUS537C AUGUST 2002 REVISED MARCH 2004
www.ti.com
7
APPLICATION INFORMATION
OVERVIEW
With the addition of power via media-dependent interface (MDI) to the IEEE 802.3af Standard, all data terminal
equipment (DTE) now has the option to receive power over existing cabling that is used for data transmission.
The IEEE 802.3af Standard defines the requirements associated with providing and receiving power over the
existing cabling. The power sourcing equipment (PSE) provides the power on the cable and the powered device
(PD) receives the power. As part of the IEEE 802.3af Standard, the interface between the PSE and PD is
defined as it relates to the detection and classification protocol.
POWER SOURCING EQUIPMENT DETECTION OF A POWERED DEVICE
A powered device (PD) draws power or requests power by participating in a PD detection algorithm. This
algorithm requires the power sourcing equipment (PSE) to probe the link looking for a valid PD. The PSE probes
the link by sending out a voltage between 2.8 V and 10 V across the power lines. A valid PD detects this voltage
and places a resistance of between 23.75 k
and 26.25 k across the power lines. Naturally, the current varies
depending on the input voltage. On detecting this current, the PSE concludes that a valid PD is connected at the
end of the ethernet cable and is requesting power.
If the powered device (PD) is in a state in which it does not accept power, the PD is required to place a
resistance above or below the values listed for a valid PD. On the lower end, a range between 12 k
and
23.75 k
signifies that the PD does not require power. On the higher end, the range is defined to be between
26.25 k
and 45 k . Any resistance value less than 12 k and greater than 45 k, is interpreted by the PSE
as a nonvalid PD detection signature.
The TPS2370 participates in the detection algorithm by activating an internal FET, which connects the DET pin of
the device to VEE. As a result, any resistance connected between VDD and the DET pin of the TPS2370 is, in
effect, across the power lines. This internal FET is active only when input power to the PD is between 2.8 V and
10 V.
POWER SOURCING EQUIPMENT CLASSIFICATION OF A POWERED DEVICE
After the detection phase, the PSE can optionally initiate a classification of the PD. The classification of a PD is
used by the PSE to determine the maximum power required by the PD during normal operation. Five different
levels of classification are defined by the IEEE 802.3af Standard. These levels are shown in Table 2.
Table 2. Powered Device Classification Levels
CLASS
USAGE
POWER DEVICE
POWER
(W)
CLASSIFICATION
CURRENT
(mA)
MIN
MAX
MIN
MAX
0
Default
0.44
12.95
0
4
1
Optional
0.44
3.84
9
12
2
Optional
3.84
6.49
17
20
3
Optional
6.49
12.95
26
30
4
Not allowed
reserved for future use
36
44
Classification of the PD is optionally performed by the PSE only after a valid PD has been detected. To
determine PD classification, the PSE increases the voltage across the power lines to between 15.5 V and 20.5 V.
The amount of current drawn by the PD determines the classification (see Table 2).
When the input voltage to the TPS2370 is between 14.0 V and 20.5 V, the TPS2370 uses an internal regulator to
generate a fixed voltage on the CLASS pin. A resistor connected between the CLASS pin and VEE draws a fixed
amount of current and thereby defines the classification level of the PD.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS23753PW | 0.505 A SWITCHING CONTROLLER, 273 kHz SWITCHING FREQ-MAX, PDSO14 |
| TPS2376DDA-HG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2376DDAR-H | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2376DDA-H | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2390DGKR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2370PWG4 | 功能描述:熱插拔功率分布 IEEE 802.3af Pwr Ifc Switch For PoE PD’s RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2370PWR | 功能描述:熱插拔功率分布 IEEE 802.3af Pwr Ifc Switch For PoE PD’s RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2370PWRG4 | 功能描述:熱插拔功率分布 IEEE 802.3af Pwr Ifc Switch For PoE PD’s RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2371D | 功能描述:熱插拔功率分布 Legacy/IEEE802.3af Comp Pwr InterfSw RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2371DG4 | 功能描述:熱插拔功率分布 Legacy/IEEE802.3af Comp Pwr InterfSw RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。