- 您現在的位置：買賣IC網 > PDF目錄68612 > TPS2398DGKRG4 (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 PDF資料下載
參數資料
| 型號： | TPS2398DGKRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | GREEN, PLASTIC, MSOP-8 |
| 文件頁數： | 9/27頁 |
| 文件大?。?/td> | 792K |
| 代理商： | TPS2398DGKRG4 |
TPS2398
TPS2399
SLUS562A JUNE 2003 REVISED SEPTEMBER 2003
17
www.ti.com
APPLICATION INFORMATION
If the result of equation (4) is larger than the maximum input supply value, then the load can be expected to
charge completely during the inrush slewing portion of the insertion event. However, if this voltage is less than
the maximum supply input, VIN(max), the HSPM transitions to the constant-current charging of the load. The
remaining amount of time required at IMAX is determined from equation (5).
t
CC +
C
LOAD
V
IN (max) * VLSS
V
REF_K (min)
R
SENSE
where:
t
CC is the constant-current voltage ramp time, in seconds, and
V
REF_K(min) is the minimum clamp voltage, 33 mV.
With this information, the minimum recommended value timing capacitor CFLT can be determined. The delay
time needed will be either a time tSS2 or the sum of tSS2 and tCC, according to the estimated time to charge the
load. The quantity tSS2 is the duration of the normal rate current ramp period, and is given by equation (6).
t
SS2 +
0.35
C
RAMP
where:
C
RAMP is given in microfarads
Since fault timing is generated by the constantcurrent charging of CFLT, the capacitor value is determined from
either equation (7) or (8), as appropriate.
C
FLT(min) +
55
t
SS2
3.75
C
FLT(min) +
55
t
SS2 )
t
CC
3.75
where:
C
FLT(min) is the recommended capacitor value, in microfarads,
t
SS2 is the result of equation (6), in seconds, and
t
CC is the result of equation (5), in seconds.
Continuing the typical application example, using a 100-
F input capacitor (CLOAD), equations (3) and (4)
estimate the load voltage ramping to approximately 46 V during the soft-start period. If the module should
operate down to 72 V input supply, approximately another 1.58-ms of constant-current charging may be
required. Therefore, equations (6) and (8) are used to determine CFLT(min), and the result of 0.043-F suggests
the 0.047-
F standard value.
(5)
(6)
(7)
(8)
相關PDF資料 |
PDF描述 |
|---|---|
| TPS3802L30DCK | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS3801T50DCKT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS3801E18DCK | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS3801-01DCKRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS3802L30DCKRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2398EVM | 功能描述:電源管理IC開發工具 TPS2398 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS2399D | 制造商:Texas Instruments 功能描述: |
| TPS2399DGK | 功能描述:熱插拔功率分布 Simple -48V Controller w/Enable RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2399DGKG4 | 功能描述:熱插拔功率分布 Simple -48V Controller w/Enable RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2399DGKR | 功能描述:熱插拔功率分布 Simple -48V Controller w/Enable RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。