- 您現在的位置：買賣IC網 > PDF目錄98280 > TPS24710 (TEXAS INSTRUMENTS INC) POWER SUPPLY SUPPORT CKT, PDSO10 PDF資料下載
參數資料
| 型號： | TPS24710 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, PDSO10 |
| 封裝： | GREEN, PLASTIC, MSOP-10 |
| 文件頁數： | 19/34頁 |
| 文件大?。?/td> | 2148K |
| 代理商： | TPS24710 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
GATE
ISS
VCC
t
C
I
C
V
D
=
-
÷
è
Partof
TPS2471x
M
1
ToLoad
GND
GATE
FromSource
R
GATE
1k
C
GATE
S0509-02
I
30 A
GATE
SLVSAL2C
– JANUARY 2011 – REVISED MAY 2011
(14)
Figure 36. Gate Capacitor (dV/dt) Control Inrush Mode.
ADDITIONAL DESIGN CONSIDERATIONS
Use of PG/PGb
Use the PG/PGb pin to control and coordinate a downstream dc/dc converter. If this is not done, then a long time
delay is needed to allow COUT to fully charge before the converter starts. An undesirable latch-up condition can
be created between the TPS24710/11/12/13 output characteristic and the dc/dc converter input characteristic if
the converter starts while COUT is still charging; the PG/PGb pin is one way to avoid this
Output Clamp Diode
Inductive loads on the output may drive the OUT pin below GND when the circuit is unplugged or during a
current-limit event. The OUT pin ratings can be satisfied by connecting a diode from OUT to GND. The diode
should be selected to control the negative voltage at the full short-circuit current. Schottky diodes are generally
recommended for this application.
Gate Clamp Diode
The TPS24710/11/12/13 has a relatively well-regulated gate voltage of 12 V to 15.5 V with a supply voltage VVCC
higher than 4 V. A small clamp Zener from gate to source of M1 is recommended if VGS of M1 is rated below 12
V. A series resistance of several hundred ohms or a series silicon diode is recommended to prevent the output
capacitance from discharging through the gate driver to ground.
High-Gate-Capacitance Applications
Gate voltage overstress and abnormally large fault current spikes can be caused by large gate capacitance. An
external gate clamp Zener diode is recommended to assist the internal Zener if the total gate capacitance of M1
exceeds about 4000 pF. When gate capacitor dV/dt control is used, a 1-k
Ω resistor in series with CGATE is
recommended (see Figure 36). If the series R-C combination is used for MOSFETs with CISS less than 3000 pF,
then a Zener diode is not necessary.
26
Copyright
2011, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TPS24711 | POWER SUPPLY SUPPORT CKT, PDSO10 |
| TPS24711DGSR | POWER SUPPLY SUPPORT CKT, PDSO10 |
| TPS2481PW | POWER SUPPLY SUPPORT CKT, PDSO20 |
| TPS2480PW | POWER SUPPLY SUPPORT CKT, PDSO20 |
| TPS2490DGSRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS24710DGS | 功能描述:熱插拔功率分布 2.5-18V Hi Eff Hot- Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS24710DGSR | 功能描述:熱插拔功率分布 2.5-18V Hi Eff Hot- Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS24710EVM-003 | 功能描述:電源管理IC開發工具 TPS24710 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS24711DGS | 功能描述:熱插拔功率分布 2.5-18V Hi Eff Hot- Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS24711DGSR | 功能描述:熱插拔功率分布 2.5-18V Hi Eff Hot- Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。