- 您現在的位置：買賣IC網 > PDF目錄98280 > TPS24711 (TEXAS INSTRUMENTS INC) POWER SUPPLY SUPPORT CKT, PDSO10 PDF資料下載
參數資料
| 型號： | TPS24711 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, PDSO10 |
| 封裝： | GREEN, PLASTIC, MSOP-10 |
| 文件頁數： | 6/34頁 |
| 文件大?。?/td> | 2148K |
| 代理商： | TPS24711 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
SLVSAL2C
– JANUARY 2011 – REVISED MAY 2011
SYSTEM OPERATION
INTRODUCTION
The TPS24710/11/12/13 provides all the features needed for a positive hot-swap controller. These features
include:
Undervoltage lockout
Adjustable (system-level) enable
turn-on inrush limiting
High-side gate drive for an external N-channel MOSFET
MOSFET protection by power limiting
Adjustable overload timeout
— also called an electronic circuit breaker
Charge-complete indicator for downstream converter coordination
A choice of latch (TPS24710/12) or automatic restart mode (TPS24711/13)
The typical application diagram on the front page of this data sheet, and oscilloscope plots shown in Figure 26
through Figure 28 and Figure 30 through Figure 33, demonstrate many of the functions described previously.
BOARD PLUG IN
Figure 26 and Figure 27 illustrate the inrush current that flows when a hot swap board under the control of the
TPS24710/11/12/13 is plugged into a system bus. Only the bypass capacitor charge current and small bias
currents are evident when a board is first plugged in. The TPS24710/11/12/13 is held inactive, for a short period
while internal voltages stabilize. During this period GATE, PROG, TIMER are held low and PG, FLT, PGb, and
FLTb are held open drain. When the voltage on the internal VCC rail exceeds approximately 1.5 V, the power-on
reset (POR) circuit initializes the TPS24710/11/12/13 and a start-up cycle is ready to take place.
GATE, PROG, TIMER, PG, FLT, PGb, and FLTb are released after the internal voltages have stabilized and the
external EN (enable) thresholds have been exceeded. The part begins sourcing current from the GATE pin to
turn on MOSFET M1. The TPS24710/11/12/13 monitors both the drain-to-source voltage across MOSFET M1
and the drain current passing through it. Based on these measurements, the TPS24710/11/12/13 limits the drain
current by controlling the gate voltage so that the power dissipation within the MOSFET does not exceed the
power limit programmed by the user. The current increases as the voltage across the MOSFET decreases until
finally the current reaches the current limit ILIM.
14
Copyright
2011, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TPS24711DGSR | POWER SUPPLY SUPPORT CKT, PDSO10 |
| TPS2481PW | POWER SUPPLY SUPPORT CKT, PDSO20 |
| TPS2480PW | POWER SUPPLY SUPPORT CKT, PDSO20 |
| TPS2490DGSRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| TPS2490DGSR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS24711DGS | 功能描述:熱插拔功率分布 2.5-18V Hi Eff Hot- Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS24711DGSR | 功能描述:熱插拔功率分布 2.5-18V Hi Eff Hot- Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS24711EVM-004 | 功能描述:電源管理IC開發工具 TPS24711 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS24712DGS | 功能描述:熱插拔功率分布 2.5-18V Hi Eff Pwr- Ltd Hot-Swap Cntrlr RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS24712DGSR | 功能描述:熱插拔功率分布 2.5-18V Hi Eff Pwr- Ltd Hot-Swap Cntrlr RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。