- 您現在的位置：買賣IC網 > PDF目錄383962 > TPS2490EVM-001 (Texas Instruments, Inc.) +48V Hot Swap Power Manager Evaluation Kit(在+48V熱插拔電源管理中應用的評估) PDF資料下載
參數資料
| 型號： | TPS2490EVM-001 |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | +48V Hot Swap Power Manager Evaluation Kit(在+48V熱插拔電源管理中應用的評估) |
| 中文描述： | 48V熱插拔電源管理評估套件（在48V的熱插拔電源管理中應用的評估） |
| 文件頁數： | 18/24頁 |
| 文件大?。?/td> | 170K |
| 代理商： | TPS2490EVM-001 |
Equipment Requirements
3-2
3.1
Equipment Requirements
The following test equipment is required to use the EVM kit.
Power supply, 60 VDC at 6 amp minimum
Oscilloscope, 4 channel preferred (3 voltage probes and 1 current probe)
Digital voltmeter (DVM)
The availability of additional DVMs simplifies EVM use.
3.2
Verifying the EVM Operation
The following procedure steps may be used to verify functional operation of
the EVM after receipt.
3.2.1
Equipment Setup
1)
Do not connect the power supply to the EVM boards (HPA016 and
HPA018).
2)
If installed, remove the EVM main board (HPA016) from the P1B
connector of the EVM backplane board (HPA018).
3)
On the EVM main board (HPA016), set switch S1 to MANU.
4)
On the EVM backplane board (HPA018), set switch SW1 to OFF.
5)
Turn on the power supply. Set the output voltage of the supply to 48
±
0.2
VDC. On the supply, verify the output current limit control is set to allow
sourcing of at least 6 A.
6)
Turn off the power supply. Connect the power supply to the EVM back-
plane board (HPA018) as shown in Figure 31.
Figure 31.+48 V Hot-Swap EVM Setup
TPS2490EVM
Or
TPS2491EVM
Main Board
Unit Under Test (UUT)
TP15
TP6
Oscilloscope
CH 1
CH 2
CH 3
CH 4
Power
Supply
(+48 V)
+
Current Probe
J3B (GND)
J4B (+48VIN)
Backplane Board
+
+
+
J4(GND)
TP3
Reference
相關PDF資料 |
PDF描述 |
|---|---|
| TPS3106K33DBV | UltraLow Supply-Current/Supply-Voltage Supervisory Circuits |
| TPS3600D50PWRG4 | BATTERY-BACKUP SUPERVISORS FOR LOW-POWER PROCESSORS |
| TPS3600x20PW | BATTERY-BACKUP SUPERVISORS FOR LOW-POWER PROCESSORS |
| TPS3600x20PWR | BATTERY-BACKUP SUPERVISORS FOR LOW-POWER PROCESSORS |
| TPS3600x25PW | BATTERY-BACKUP SUPERVISORS FOR LOW-POWER PROCESSORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2491DGS | 功能描述:熱插拔功率分布 Retry Pos Hi-Voltage Pwr-Limiting RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2491DGSG4 | 功能描述:熱插拔功率分布 Retry Pos Hi-Voltage Pwr-Limiting RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2491DGSR | 功能描述:熱插拔功率分布 Retry Pos Hi-Voltage Pwr-Limiting RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2491DGSRG4 | 功能描述:熱插拔功率分布 Retry Pos Hi-Voltage Pwr-Limiting RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2491EVM-002 | 功能描述:電源管理IC開發工具 TPS2491-002 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。